JVC Computer Monitor TM H1750CG User Manual

TM-H1750CG  
[ TM-H1750CG/E / TM-H1750CG/U ]  
OPERATING INSTRUCTIONS  
COLOR VIDEO MONITOR  
INSTRUCTIONS  
TM-H1750CG  
For Customer Use:  
Enter below the Serial No. which is located on the rear of the cabinet.  
Retain this information for future reference.  
Pour l’usage du client:  
Enter ci-dessous le numéro de série qui est situé sur l’arrière du coffret.  
Conserver cette information pour une référence ultérieure.  
Model No. :  
Numéro de modèle :  
TM-H1750CG  
Serial No. :  
Numéro de série :  
UNDER COLOR  
SCAN OFF  
BLUE  
CHECK ASPECT  
POWER  
CHROMA CONTRAST  
VOLUME/SELECT  
MENU  
A
B
C
SLOT  
D
PHASE  
BRIGHT  
INPUT SELECT  
TM-H1750CG  
LCT1025-001A-H  
1101-Y-U-JMT  
Jan. 2002 No. 51923  
 
POWER CONNECTION  
The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 230 V (For European countries  
or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power  
cord designated to ensure Safety and EMC regulations of each countries.  
SAFETY PRECAUTIONS  
In order to prevent any fatal accidents caused by misoperation  
FCC INFORMATION (U.S.A. only)  
Power cord  
or mishandling the monitor, be fully aware of all the following  
precautions.  
CAUTION: Changes or modification not approved by  
JVC could void the user's authority to operate the  
equipment.  
WARNINGS  
To prevent fire or shock hazard, do not expose this  
monitor to rain or moisture. Dangerous high voltages  
are present inside the unit. Do not remove the back  
cover of the cabinet. When servicing the monitor,  
consult qualified service personnel. Never try to service  
it yourself.  
Power supply voltage : AC 120 V  
Countries: U.S.A.  
AC 230 V  
Canada  
AC 230 V  
countries  
NOTE: This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is  
no guarantee that interference will not occur in a  
particular installation. If this equipment does cause  
harmful interference to radio or television reception,  
which can be determined by turning the equipment off  
and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and  
receiver.  
and  
European  
United  
Kingdom  
Warning:  
Do not use the same Power Cord for AC 120 V as for AC 230 V. Doing so may cause malfunction, electric shock  
or fire.  
Note for the United Kingdom power cord only  
The plug on the United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a correctly rated  
approved type, re-fit the fuse cover.  
(Consult your dealer or qualified service personnel.)  
WARNING : THIS APPARATUS MUST  
BE EARTHED.  
Machine Noise Information Ordinance 3. GSGV,  
January 18, 1991: The sound pressure level at the  
operator position is equal or less than 70 dB(A)  
according to ISO 7779.  
How to replace the fuse  
Open the fuse compartment with the blade screw driver, and  
replace the fuse.  
(* An example is shown in the illustration.)  
Fuse  
Improper operations, in particular alternation of high  
voltage or changing the type of tube may result in x-ray  
emission of considerable dose. A unit altered in such a  
way no longer meets the standards of certification, and  
must therefore no longer be operated.  
– Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV  
technician for help.  
SCREEN BURN  
It is not recommended to keep a certain still image displayed on screen for a long time as well as displaying extremely bright  
images on screen. This may cause a burning (sticking) phenomenon on the screen of cathode-ray tube. This problem does  
not occur as far as displaying normal video playback motion images.  
This monitor is equipped with a 3-blade grounding-type  
plug to satisfy FCC rule. If you are unable to insert the  
plug into the outlet, contact your electrician.  
Notice (U.S.A. only)  
This product utilizes both a Cathode Ray Tube (CRT) and  
other components that contain lead. Disposal of these  
materials may be regulated in your community due to  
environmental considerations. For disposal or recycling  
information please contact your local authorities, or the  
Electronics Industries Alliance: <http://www.eiae.org.>  
CONTENTS  
SAFETY PRECAUTIONS ................................................................................. 2  
CONTROLS AND FEATURES ......................................................................... 4  
PRECAUTIONS  
Use only the power source specified on the unit.  
(120 V AC/230 V AC, 50 Hz/60Hz)  
Unplug this unit from the AC outlet and refer servicing to  
qualified service personnel under the following conditions:  
– when the power cord is frayed or the plug is damaged,  
– if liquid has been spilled into the unit,  
– if the unit has been dropped or the cabinet has been  
damaged,  
CONTROLS AND FEATURES (INPUT CARD: OPTIONAL) ........................................  
7
When not using this unit for a long period of time, or when  
cleaning it, be sure to disconnect the power plug from the  
AC outlet.  
Do not allow anything to rest on the power cord. And do not  
place this unit where people will tread on the cord. Do not  
overload wall outlets or power cords as this can result in a  
fire or electric shock.  
Avoid using this unit under the following conditions:  
– in extremely hot, cold or humid places,  
– in dusty places,  
– near appliances generating strong magnetic fields,  
– in places subject to direct sunlight,  
– in badly ventilated places,  
– in automobiles with doors closed.  
Do not cover the ventilation slots while in operation as this  
could obstruct the required ventilation flow.  
When dust accumulates on the screen surface, clean it with  
a soft cloth.  
PREPARATION................................................................................................. 8  
HOW TO HANDLE BASIC OPERATIONS ....................................................... 9  
HOW TO USE THE MENU FUNCTIONS.........................................................11  
HOW TO INITIALIZE THE SETTING.............................................................. 14  
BASIC CONNECTION EXAMPLE.................................................................. 15  
HOW TO USE EXTERNAL CONTROL .......................................................... 17  
TROUBLESHOOTING.................................................................................... 18  
SPECIFICATIONS .......................................................................................... 19  
APPENDIX...................................................................................................... 20  
– when the unit exhibits a distinct change in performance.  
Do not attempt to service this unit yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Always refer servicing to qualified service  
personnel.  
When replacement parts are required, have the service  
personnel verify in writing that the replacement parts he/  
she uses have the same safety characteristics as the  
original parts. Use of manufacture’s specified replacement  
parts can prevent fire, shock, or other hazards.  
Upon completion of any servicing or repair work to this unit,  
please ask the service personnel to perform the safety  
check described in the manufacturer’s service literature.  
When this unit reaches the end of its useful life, improper  
disposal could result in a picture tube implosion. Ask  
qualified service personnel to dispose of this unit.  
2
3
 
CONTROLS AND FEATURES  
FRONT VIEW  
REAR VIEW  
<Front Panel>  
<Rear Panel>  
VIDEO A  
1
16  
17  
18  
19  
REMOTE  
UNDER COLOR  
BLUE  
CHECK ASPECT  
POWER  
CHROMA CONTRAST  
VOLUME/SELECT  
MENU  
IN  
VIDEO B  
OUT  
A
B
C
SLOT  
D
SCAN  
OFF  
15  
PHASE  
BRIGHT  
INPUT SELECT  
VIDEO  
VIDEO  
A
IN  
OUT  
Y/C  
IN  
OUT  
B
IN  
IN  
OUT  
Y/C  
2
3
4
5
6
7
8
9
10 11  
12  
13 14  
U
N
D
E
R
C
O
L
O
R
B
L
U
E
POWER  
C
H
R
O
M
A
C
O
N
T
R
A
S
T
V
O
L
U
M
E
/
S
E
L
E
C
T
M
E
N
U
S
C
A
N
O
F
F
C
H
E
C
K
A
S
P
E
C
T
A
B
C
SLOT  
D
P
H
A
S
E
BR  
I
G
H
T
I
N
P
U
T
S
E
L
EC  
T
TM-H1750CG  
OUT  
IN  
AUDIO  
A
20  
IN  
OUT  
OUT  
AUDIO  
B
IN  
1
2
Tally lamp  
8 Blue Check button [BLUE CHECK]  
OUT  
Lights when the tally control signal is ON. The tally control  
signal is input through the REMOTE (external control)  
remote terminal. For details, refer to Page 17.  
Cuts red and green signal components. Only blue signal  
components are shown. Press the button again to  
restore the normal image.  
AUDIO A  
21  
22  
OUT  
OUT  
IN  
AUDIO B  
When selected, this button lights.  
Chroma/Phase button  
Aspect button [ASPECT]  
[
CHROMA/  
PHASE]  
9
IN  
Press this button to change the aspect ratio from 4:3 to  
16:9.  
Press this button to activate the picture color density  
adjustment mode or picture hue adjustment mode. Each  
time you press the button, the adjustment item changes.  
Input card slot (SLOT)  
Optional input cards can be installed in this slot. Input  
cards are not provided when you purchase this monitor.  
16  
17  
Notes:  
* For corresponding audio signals, use the AUDIO B  
terminals  
10 Input A (VIDEO) button [INPUT SELECT A]  
Selects the video and audio signals input to the VIDEO A  
Picture color density  
f
Picture hue  
*
and AUDIO A  
button lights when selected.  
q
terminals on the rear panel. The  
Adjust the value with the VOLUME/SELECT buttons  
Also used as a control button in the menu function mode.  
4
.
w
.
* When both VIDEO B terminals are connected (input) at  
the same time, the Y/C terminal has priority.  
* Also refer to BASIC CONNECTION EXAMPLE  
on page 16.  
REMOTE (external control) terminal  
Connect this terminal to an external control unit to enable  
remote operation of the monitor.  
Refer to the HOW TO USE EXTERNAL CONTROL on  
page 17 for more details.  
11 Input B (VIDEO Y/C) button [INPUT SELECT B]  
Selects the video and audio signals input to the VIDEO B  
Contrast/Brightness button  
[CONTRAST / BRIGHT  
Press this button to activate the picture contrast adjustment  
mode or picture brightness adjustment mode. Each time  
you press the button, the adjustment item changes.  
3
]
(
or VIDEO B (Y/C)  
the rear panel. The button lights when selected.  
)
and AUDIO B  
w
terminals on  
Audio A terminals [AUDIO A IN/OUT]  
Input (IN) and output (OUT) terminals for the audio signal  
21  
Note:  
Video A terminals [VIDEO A IN/OUT]  
Video signal input (IN) and output (OUT) terminals.  
The output terminal is bridge-connected.  
: Video signal input terminal  
OUT : Bridge-connected video signal output terminal  
18  
19  
20  
The VIDEO B terminals include a video terminal (BNC  
connector) and a Y/C terminal (mini-DIN 4-pin connector).  
The Y/C (S-video) terminal has priority.  
corresponding to the VIDEO A terminals  
The output terminal is bridge-connected.  
*.  
Picture contrast  
f
Picture brightness  
Adjust the value with the VOLUME/SELECT buttons  
Also used as a control button in the menu function mode.  
4
.
IN  
: Audio signal input terminal  
IN  
OUT : Bridge-connected audio signal output terminal  
12 Input C/D (Slot) buttons [INPUT SELECT C/D  
Volume/Select buttons  
[VOLUME/SELECT  
Adjusts the speaker volume. Also used as a control  
button in the menu function mode.  
4
5
(SLOT)]  
Notes:  
Notes:  
+]  
Selects the signals to be input via the input cards installed  
in the rear panel card slots.  
C, D: Selects the image from the input card in the slot.  
For details on input connectors and using the INPUT  
SELECT button, refer to page 7.  
* For corresponding video signals, use the VIDEO A  
* For corresponding audio signals, use the AUDIO A  
terminal  
*.  
terminals  
q.  
* Also refer to BASIC CONNECTION EXAMPLE  
on pages 15 and 16.  
* Also refer to BASIC CONNECTION EXAMPLE  
on page 15.  
Menu button [MENU]  
Displays and disappears the <MENU> screen.  
Pressing the CHROMA/PHASE button  
button depressed will display the <SET-UP MENU>  
screen.  
Audio B terminals [AUDIO B IN/OUT]  
Input (IN) and output (OUT) terminals for the audio  
22  
Video B terminals [VIDEO B IN/OUT]  
Video signal input (IN) and output (OUT) terminals.  
The output terminal is bridge-connected.  
: Video signal input terminal  
OUT : Bridge-connected video signal output terminal  
Power indicator  
13  
14  
2
with the Menu  
Unlit  
: The main power is OFF.  
signals corresponding to the VIDEO B terminals  
VIDEO B (Y/C) terminals  
The output terminal is bridge-connected.  
IN : Audio signal input terminal  
(
or  
Orange : The main power is ON, but the monitor’s power  
is OFF (in the stand-by mode).  
Green : The main power is ON, and the monitor’s power  
is ON (in the normal operation mode).  
).  
IN  
Under Scan button [UNDER SCAN]  
Reduces the screen size to display the entire image.  
Press the button again to cancel Under Scan.  
When selected, the Under Scan button lights.  
6
7
Notes:  
OUT : Bridge-connected audio signal output terminal  
Power switch [POWER  
]
* For corresponding audio signals, use the AUDIO B  
Press the power switch to turn the monitor’s power ON or  
OFF when the main power is ON.  
Notes:  
Color Off button [COLOR OFF]  
terminals  
w.  
* Also refer to BASIC CONNECTION EXAMPLE on  
page 15.  
Cuts color signals to display a black and white image.  
Press the button again to restore the original color.  
When selected, the COLOR OFF button lights.  
* For corresponding video signals, use the VIDEO B  
Note:  
terminals ( or VIDEO B (Y/C) terminals  
).  
When RUSH DELAY is set to SLOW, it takes about  
three seconds before power is actually supplied after  
the power switch is pressed.  
* Also refer to BASIC CONNECTION EXAMPLE  
on pages 15 and 16.  
Video B (Y/C) terminals [VIDEO B Y/C IN/OUT]  
Y/C (S-video) signal input (IN) and output (OUT) termi-  
nals. The output terminal is bridge-connected.  
Note:  
This function is invalid with RGB input.  
15 Speaker  
A built-in speaker is located inside the right side panel  
when the monitor is viewed from the front.  
IN  
: Y/C-separated (S-video) video signal input  
terminal  
OUT : Bridge-connected Y/C-separated (S-video) signal  
output terminal.  
4
5
 
CONTROLS AND FEATURES  
CONTROLS AND FEATURES (cont’d)  
REAR VIEW  
(INPUT CARD: OPTIONAL)  
COMPONENT/RGB INPUT CARD (OPTIONAL:  
<Rear Panel>  
IF-C01COMG)  
1
Video input/output terminals  
Input (IN) and output (OUT) terminals for component  
(color deference) or RGB signals.  
The IN and OUT terminals are bridge-connected.  
(When no cable is connected to the OUT terminal, the  
input signal is automatically terminated.)  
REMOTE  
G/Y  
25  
To AC outlet  
(120 V AC,  
50 Hz/60 Hz)  
For U.S.A. and Canada  
IN  
OUT  
B/P  
B
R
/B-Y  
Select component signal : press INPUT SELECT C button  
1
Select RGB signal  
: press INPUT SELECT D button  
VIDEO  
VIDEO  
A
IN  
OUT  
IN  
OUT  
R/P  
/B-Y  
To AC outlet  
(230 V AC,  
50 Hz/60 Hz)  
B
Synchronized signal input/output terminals  
Input (IN) and output (OUT) terminals for the vertical,  
horizontal or complex synchronized signals.  
The synchronized signals from these terminals have  
priority over other terminals. When no synchronized signal  
is input to these terminals, the synchronized signal from  
the video input/output terminals (G/Y terminals) is valid.  
The IN and OUT terminals are bridge-connected.  
(When no cable is connected to the OUT terminal, the  
input signal is automatically terminated.)  
IN  
IN  
OUT  
Y/C  
2
25  
25  
OUT  
IN  
IN  
IN  
OUT  
OUT  
OUT  
AUDIO  
A
HD/C  
VD  
S
4
IN  
OUT  
OUT  
AUDIO  
B
For Europe  
IN  
2
3
AUDIO  
For the United Kingdom  
24  
23  
IN  
OUT  
External sync is available with RGB input only. G on  
SYNC cannot be used with RGB input.  
Audio input/output terminals  
3
4
Compatible signal formats:  
480/50i, 480/60i  
Input (IN) and output (OUT) terminals for audio signals.  
The IN and OUT terminals are bridge-connected.  
Main power switch  
25 Power cord  
Connects the provided power cord (120 V AC or  
230 V AC, 50 Hz/60 Hz) to the AC IN connector  
23  
24  
Connection terminal (to a Color Video Monitor)  
Attach to the connection terminal of your color video  
monitor.  
Press the switch to turn the main power ON or OFF. When  
the main power is ON, the power lamp on the front panel  
lights in orange and the monitor enters the stand-by  
mode.  
r
.
Caution:  
In North America (USA and Canada), this monitor comes  
with one power cable. In Europe and the United King-  
dom, two power cables are provided (one for use in  
continental European countries and the other for the UK).  
Be sure to use the power cable that is appropriate for the  
AC outlets used in your region. If none of the power  
cables provided is suitable, please contact your dealer or  
qualified service personnel to obtain the correct type of  
power cable.  
I : ON : OFF  
SDI INPUT CARD (OPTIONAL: IF-C01SDG)  
AC inlet [AC IN]  
Power input connector. Connect the provided AC power  
1 Output terminal for a selected component  
cord  
50 Hz/60 Hz).  
t
to an AC outlet (120 V AC or 230 V AC,  
serial digital signal  
SWITCHED  
OUT  
Output terminal for a selected digital signal (the input  
displayed on the screen). The output signal is cable-  
compensated.  
1
2
NOTE: When the monitor’s main power is OFF, no digital  
signal is output.  
In the standby mode, signals from the SDI 1 connector  
are output.  
IN  
IN  
SDI  
SDI  
1
2
4
2 Input terminals for component serial digital  
signals  
AUDIO1  
Input terminals for the digital signal.  
Select SDI 1 : press INPUT SELECT C button  
Select SDI 2 : press INPUT SELECT D button  
IN  
OUT  
3
3
Audio input/output terminals  
AUDIO2  
Input (IN) and output (OUT) terminals for the analog  
signals corresponding to SDI 1 and SDI 2.  
NOTE: This input card cannot decode audio data even if  
contained in the input digital signal.  
Compatible signal formats: 480/60i, 480/50i  
Note:  
4 Connection terminal (to a Color Video  
The optional input cards shown below cannot be used.  
Using any of these cards will void your warranty and may  
result in damage or malfunction.  
Monitor)  
Attach to the connection terminal of your color video  
monitor.  
*Video input card (IF-C01PNG)  
*HD-SDI input card (IF-C01HSDG)  
7
6
 
PREPARATION  
HOW TO HANDLE BASIC  
OPERATIONS  
BASIC OPERATION  
INSTALLING THE INPUT CARD  
STATUS indication  
(PAL or NTSC)  
1. Press the main power switch to turn on the power.  
2. Press the POWER switch to turn on the power.  
ON :Power turns ON. (Power indicator: lit)  
1. Turn off the Color Video Monitors main power and unplug the power cable  
from the AC outlet.  
2. Unscrew the screws and remove the slot cover from the slot (on the rear side  
of the monitor) in which you are going to install the card.  
PAL  
POWER  
Green : The main power is ON, and the monitor’s  
power is ON (in the normal operation mode).  
OFF :Power turns OFF. (Power indicator: unlit)  
Orange : The main power is ON, but the monitor’s  
power is OFF (in the standby mode)  
Rear side of the TM-H1750CG  
color video monitor  
Unlit  
: The main power is OFF.  
REMOTE  
3. Press the INPUT SELECT buttons to choose input.  
About the STATUS indication  
Select video/audio signals input to terminals on the rear  
panel. The selected button lights in green.  
With the COLOR SYSTEM setting set  
to AUTO mode, when you turn on the  
power or select inputs, the color  
A
B
C
SLOT  
D
INPUT  
SELECT  
buttons  
Terminals on the rear panel  
Slot cover  
system indication appears for about  
3 seconds on the screen while PAL or  
NTSC signals are being detected.  
It does not appear when receiving a  
B/W signal or when no signal is input.  
Refer to page 11 for more information  
about COLOR SYSTEM setting and  
page 12 for more information about  
STATUS indication setting.  
INPUT SELECT  
VIDEO  
VIDEO  
A
Video signal input  
Audio signal input  
IN  
OUT  
B
1
Input A  
(VIDEO)  
VIDEO A terminal  
AUDIO A terminal  
IN  
IN  
OUT  
Y/C  
2
Input B  
(VIDEO/Y/C)  
VIDEO B terminal  
AUDIO B terminal  
VIDEO B (Y/C) terminal  
3
4
Input C  
Input D  
Refer to page 7 for details about the input terminals  
on each card and the INPUT SELECT button.  
3. Insert the Input Cards board (green-colored) into the slot, fitting the board into  
the guide rails on the top and bottom of the slot.  
Note: The Y/C (S-video) terminal has priority.  
00 ~ 50  
Fit the board to  
the guide rails.  
4. Press the VOLUME/SELECT buttons to adjust the  
speaker volume.  
Press this button to display the speaker volume level on the  
Knob  
REMOTE  
VOLUME/SELECT  
screen.  
+ : The Built-in speaker volume is increased. (00 = 50)  
: The Built-in speaker volume is decreased. (50 = 00)  
* Screen indication will disappear about 10 seconds after operating.  
* The on-screen display goes off when you press MENU button.  
VOLUME  
:
20  
+
VIDEO  
VIDEO  
A
Guide rails  
IN  
OUT  
B
PICTURE ADJUSTMENT  
IN  
IN  
OUT  
Y/C  
UPPER  
1. Press select buttons corresponding to the item  
you want to adjust.  
Input card (the illustration  
shown is of the IF-C01COMG)  
–40 ~ +40  
Knob  
PHASE  
PHASE  
:
00  
00  
The item you select is displayed on the screen.  
CHROMA CONTRAST  
1
2
3
4
Chorma control : Press the CHROMA/PHASE button once.  
Phase control : Press the CHROMA/PHASE button twice.  
4. Push the Input Card in so that its front panel touches the monitors rear panel.  
5. Secure the Input Card by replacing the screws removed in Procedure 2.  
Contrast control : Press the CONTRAST/BRIGHT button once.  
Brightness control: Press the CONTRAST/BRIGHT button twice.  
PHASE  
BRIGHT  
* Pressing the CHROMA/PHASE button and CONTRAST/BRIGHT button  
alternately while the item is shown on screen restores the previous status.  
When no item is shown on screen, CHROMA and CONTRAST have priority.  
:
+
LOWER  
2. Adjust with the VOLUME/SELECT buttons.  
Notes:  
REMOTE  
Phase control is effective only in the  
NTSC color system mode.  
Chroma control is not effective when  
receiving RGB and B/W or when no  
signal is input. (Except when a  
component signal is input.)  
When CHROMA is adjusted to “–40,”  
the picture becomes less colorful.  
“NO EFFECT” is displayed (for about  
3 seconds) when your selected  
function has no effect.  
To change the display position on  
screen, set UPPER or LOWER with  
ADJ. BAR POSI.  
VOLUME/SELECT button  
Items  
VOLUME/SELECT  
+
CHROMA  
(Chroma)  
lighter  
deeper  
VIDEO  
VIDEO  
A
IN  
OUT  
B
PHASE  
(Phase)  
reddish  
lower  
greenish  
higher  
IN  
IN  
OUT  
Y/C  
CONTRAST  
(Contrast)  
NOTE :Do not touch the terminal connected to the monitor or board pattern.  
BRIGHT  
(Brightness)  
darker  
brighter  
Do not remove slot covers from the monitor’s slots if they are not in use.  
* Screen indication will disappear about 10 seconds after operating.  
* The on-screen display goes off when you press MENU button.  
9
8
 
HOW TO HANDLE BASIC  
OPERATIONS (cont’d)  
HOW TO USE THE MENU FUNCTIONS  
DISPLAY AND SELECTION IN THE <MENU>  
SCREEN MODE (SETTING)  
VIDEO SIGNAL CONTROLS  
<MENU> screen  
You can set the following menu items.  
Set them depending on your needs.  
Use these buttons for video signal control.  
1
2
< MENU  
APERTURE  
>
:
:
00  
LOWER  
• APERTURE  
• ADJ. BAR POSI.  
• COLOR TEMP.  
• COLOR SYSTEM  
• COMPO. LEVEL*  
• RUSH DELAY  
UNDER SCAN  
ADJ. BAR POSI.  
COLOR TEMP.  
COLOR SYSTEM  
COMP. LEVEL  
RUSH DELAY  
: 6500  
: AUTO  
Press the UNDER SCAN button to reduce the size of display area so that the whole  
picture is displayed on screen. Use to check the picture frame.  
:
00  
: STD  
1. Press the MENU button.  
3
4
MENU  
The <MENU> screen is displayed.  
EXIT  
COLOR OFF  
* The on-screen display goes off automatically after about five  
minutes with operation performed.  
To display a black and white picture, press the COLOR OFF button to input the lumi-  
nance signal only. Use to check noise in the luminance signal or for white balance  
adjustment.  
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT  
button to select MENU items.  
CHROMA CONTRAST  
VOLUME/SELECT  
MENU  
PHASE  
BRIGHT  
Note:  
A selection mark (4) is put next to the selected item.  
CHROMA CONTRAST  
No effect with RGB input.  
<Front panel buttons>  
Front panel  
button  
Function  
displayed  
1
2
3
4
Selection mark (4): Indicates the  
menu item you select.  
Menu item: Menu items you can  
select.  
Setting display: Indicates the current  
settings (value).  
Function display: The functions of  
the front panel buttons (5 buttons on  
the left) correspond to the function  
displayed.  
Contents  
PHASE  
BRIGHT  
BLUE CHECK  
CHROMA/  
PHASE  
Forward selection mark (4)  
APERTURE  
ADJ. BAR POSI.  
COLOR TEMP.  
COLOR SYSTEM  
COMPO. LEVEL*  
RUSH DELAY  
Input the standard color-bar signal for your TV system and display it on the screen.  
When the BLUE CHECK button is pressed, the red and green signals are cut and only  
the blue signal is displayed. The BLUE CHECK function adjusts and checks CHROMA  
(COLOR) GAIN and PHASE.  
CONTRAST/  
BRIGHT  
Reverse selection mark (4  
)
Make sure that COMPO. LEVEL has been initialized when a component signal is input.  
[Procedure]  
1. Input the standard color-bar signal for your TV system and display it on the screen.  
2. Press the BLUE CHECK button.  
Function  
displayed  
3. Press the VOLUME/SELECT buttons to set.  
Contents  
3. Press the CHROMA button to adjust the chroma so that the blue bars on the left and  
right sides of the screen have the same brightness.  
4. (Only when an NTSC signal is input) Press the PHASE button to adjust the phase so  
that the two blue bars at the center of the screen have the same brightness.  
5. (Only when an NTSC signal is input) Repeat procedures 3 and 4 for the adjustment so  
that all four blue bars on the screen have the same brightness.  
Front panel  
button  
Function  
displayed  
Forward the menu item.  
Reverse the menu item.  
VOLUME/SELECT  
Contents  
+
Increase (to max. value)  
Forward the setting value  
Decrease (to min. value)  
Reverse the setting value  
VOLUME/  
SELECT (+)  
Lower the adjustment  
value. (to the minimum)  
4
VOLUME/  
SELECT (–)  
+
Raise the adjustment  
value. (to the maximum)  
1
When you have finished making the adjustment, press the BLUE CHECK button to  
deactivate.  
4
1
Forward the setting value.  
Reverse the setting value.  
Exits the <MENU> screen.  
Menu items  
APERTURE  
Purpose  
Setting range  
Picture aperture level  
Volume bar position  
00 +01  
+39 +40  
• • • • • • • • • • • •  
Initializing COMPO. LEVEL (when a component signal is input)  
EXIT  
LOWER  
6500  
UPPER  
ADJ.BAR POSI  
COLOR TEMP.  
with the IF-C01COMG component/RGB input card inserted  
When a component signal is input, be sure to adjust (initialize) the COLOR offset in  
COMPO. LEVEL.  
UPPER  
<ADJ. BAR POSI> screen  
Color temperature of white  
balance  
9300  
NTSC  
AUTO  
AUTO  
PAL  
+9 +10  
• •  
COLOR SYSTEM  
COMPO. LEVEL*  
RUSH DELAY  
Color system  
Component level  
Delay time  
BRIGHT  
:
00  
40 39  
01 00 +1  
• •  
[Procedure]  
1. Input the standard color-bar signal for your TV system and display it on the screen.  
2. Press the BLUE CHECK button.  
STD.  
SLOW  
* For normal use, leave the COLOR SYSTEM setting to AUTO.  
3. Select COMPO. LEVEL in the <MENU> screen and then adjust it with VOLUME +/–  
buttons so that the blue bars on the left and right sides of the screen have the same  
brightness.  
If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).  
* COMPO. LEVEL is displayed only with COMPONENT (SDI) input. (Shown with INPUT-C and INPUT-D  
except for RGB input.)  
BRIGHT  
:
00  
EXIT  
4. Quit the <MENU> screen and press the BLUE CHECK button.  
5. Make sure that the blue bars on the left and right sides of the screen have the same  
brightness.  
6. Repeat procedures 3, 4 and 5 for the adjustment so that the blue bars on the left and  
right sides of the screen have the same brightness.  
4. If you want to set the other menu items, repeat  
procedures 2 and 3.  
LOWER  
CHROMA CONTRAST  
VOLUME/SELECT  
MENU  
PHASE  
BRIGHT  
5. Press the MENU button to quit.  
<Front panel buttons>  
Front panel  
button  
Function  
displayed  
The upper screen; when setting  
“UPPER” in “ADJ. BAR POSI.”  
The lower screen; when setting  
“LOWER” in “ADJ. BAR POSI.”  
MENU  
Contents  
Quit (or Release) the <MENU>  
screen  
MENU  
EXIT  
10  
11  
 
HOW TO USE THE MENU  
FUNCTIONS (cont’d)  
Set-up menu items  
Purpose  
Settings  
DISPLAY AND SELECTIONS IN THE <SET-UP  
PICTURE SUB ADJ.  
Image sub adjustment  
Selects CONTRAST/BRIGHT/CHROMA/PHASE. The  
selected setting screen is shown. Select the function display for  
adjustment.  
MENU> MODE (SETTING)  
+
+
+
+
+
+
+
+
+
+
+
+
CONTRAST  
BRIGHT  
Adjusts contrast.  
Adjusts brightness.  
Adjusts color density.  
Adjusts hue.  
10  
10  
10  
10  
9
9
9
9
• •  
• •  
• •  
• •  
01 00  
01 00  
01 00  
01 00  
01 • •  
01 • •  
01 • •  
01 • •  
09  
09  
09  
09  
10  
10  
10  
10  
<SET-UP MENU> screen  
You can set the following set-up menu items.  
• PICTURE SUB ADJ.  
• H. POSITION  
V. POSITION  
• WHITE BALANCE  
• CONTROL LOCK  
• STATUS DISPLAY  
• REMOTE SYSTEM  
• INPUT REMOTE  
1
2
<SET-UP MENU>  
PICTURE SUB ADJ.  
H. POSITION  
CHROMA  
*1  
*1  
:
:
00  
00  
PHASE  
V. POSITION  
H. POSITION  
Adjusts the horizontal position of the  
screen (+: Horizontal position shifts  
to the right/-: Horizontal position shifts to  
the left)  
WHITE BALANCE  
CONTROL LOCK  
STATUS DISPLAY  
REMOTE SYSTEM  
INPUT REMOTE  
Notes:  
: OFF  
: ON  
: MAKE  
: A – D  
+
1
+
+
5
• • •  
01  
00  
• • •  
5
Parameters for H. POSITION and V. POSITION can be set separately depending on  
the signal (Input A (VIDEO), Input B (VIDEO), Input C or Input D) selected with the  
input select buttons on the front panel.  
Select the required video input with the input select buttons on the front panel in  
advance.  
V. POSITION  
Adjusts the vertical position of the screen  
(+: Vertical position moves up/-: Vertical  
position moves down)  
3
4
+
1
5
• • •  
01  
00  
• • •  
5
EXIT  
WHITE BALANCE  
Adjusts the white balance.  
Selects the drive (DRV) or cut off (CUTO) adjustment. The selected  
setting screen is shown. Select the function display for adjustment.  
WHITE BALANCE can be set independently at 6500 or 9300 for the color temperature  
value.  
Set COLOR TEMP. to 6500 or 9300 on the <MENU> screen beforehand.  
INPUT REMOTE is shown when REMOTE SYSTEM is set to MAKE.  
+
+
+
+
+
+
19  
+
19  
+
19  
+
19  
+
19  
+
20  
+
20  
+
20  
+
20  
+
20  
1  
1  
1  
1  
1  
20  
20  
20  
20  
20  
9
9
9
9
9
01 00  
01 00  
01 00  
01 00  
01 00  
01 • •  
01 • •  
01 • •  
01 • •  
01 • •  
DRIVE  
R. DRIVE  
B. DRIVE  
Adjusts red level.  
• •  
• •  
• •  
• •  
• •  
CHROMA CONTRAST  
VOLUME/SELECT  
MENU  
Adjusts blue level.  
Adjusts red cut off.  
Adjusts green cut off.  
Adjusts blue cut off.  
PHASE  
BRIGHT  
CUT OFF R. CUT OFF  
G. CUT OFF  
<Front panel buttons>  
1. While pressing the MENU button, press the  
CHROMA/PHASE button.  
B. CUT OFF  
1
2
3
4
Selection mark (4): Indicates the  
menu item you select.  
Menu item: Menu items you can  
select.  
Setting display: Indicates the  
current settings (value).  
Function display: The functions of  
the front panel buttons (5 buttons  
on the left) correspond to the  
function displayed.  
CONTROL LOCK  
Sets the operation buttons on the front  
panel to control lock mode.  
OFF  
ON  
CHROMA MENU  
The <SET-UP MENU> screen is displayed.  
* The on-screen display goes off automatically after about five  
STATUS DISPLAY  
REMOTE SYSTEM  
INPUT REMOTE  
Sets the status display of the color system. OFF  
ON  
MAKE  
TRG.  
Sets the external control function method.  
*2  
minutes with operation performed.  
PHASE  
Sets external control of input selection.  
(Shown  
AD A/B  
only  
set to MAKE.)  
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT  
button to select the desired menu item.  
*1 May not be shown depending on the type of signals input.  
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 17 for more details.  
Notes:  
A selection mark (4) is put next to the selected item.  
CHROMA CONTRAST  
Function  
displayed  
When the CONTROL LOCK function is  
set to ON, pressing operation buttons  
on the front panel will display the  
message “CONTROL LOCK ON!” on  
the screen for about 3 seconds.  
The CONTROL LOCK function is  
maintained even when the power is  
turned off.  
To turn off the CONTROL LOCK  
function, while holding the MENU button  
press the CHROMA/PHASE button.  
Then set the CONTROL LOCK function  
to OFF.  
Contents  
Front panel  
button  
Function  
displayed  
4. To set the other set-up menu items, repeat the  
procedures 2 and 3.  
Contents  
Forward the menu item.  
Reverse the menu item.  
PHASE  
BRIGHT  
CHROMA/  
PHASE  
Forward selection mark (4)  
PICTURE SUB ADJ.  
H. POSITION  
Lower the adjustment  
value. (to the minimum)  
5. Press the MENU button to quit.  
CONTRAST/  
BRIGHT  
Reverse selection mark (4  
)
V. POSITION  
+
Raise the adjustment  
value. (to the maximum)  
WHITE BALANCE  
CONTROL LOCK  
STATUS DISPLAY  
REMOTE SYSTEM  
INPUT REMOTE  
Front panel Function  
MENU  
Contents  
button  
displayed  
4
1
Forward the setting value.  
Reverse the setting value.  
Even when the CONTROL LOCK  
function is set to ON, the following  
operations are available:  
Quit (or Release) the <MENU>  
screen  
MENU  
EXIT  
Exit the <MENU>  
screen.  
– Power Switch operation  
– Volume control with the VOLUME/  
SELECT buttons  
EXIT  
DRV  
Selects DRIVE adjustment.  
– Display or disappear of the <SET-UP  
MENU> screen.  
3. Press the VOLUME/SELECT buttons to set.  
Selects CUT OFF  
adjustment.  
CUTO  
The STATUS DISPLAY function can be  
set to display (ON) or not display (OFF)  
the present color system when the  
power is turned on or the input signal is  
changed. Refer to page 9 for more  
information.  
VOLUME/SELECT  
Front panel  
button  
Function  
displayed  
Note:  
Setting  
Contents  
Adjusts red and blue  
signal level.  
RB  
Description  
+
4
Increase (to max. value)  
Forward the setting value  
VOLUME/  
SELECT (+)  
Adjusts red, green and  
blue signal level.  
MAKE  
TRG.  
A-D  
Make contact system: Controls the function with H and L (short-  
circuits or opens 15th terminal (GND)).  
RGB  
When REMOTE SYSTEM is set to  
MAKE and any one of the INPUT A to D  
buttons, the UNDER SCAN button,  
COLOR OFF button or the ASPECT  
button is pressed, “REMOTE ON!”  
appears on screen for about 3 seconds.  
(Not shown with CONTROL LOCK set  
to ON.)  
When REMOTE SYSTEM is set to  
TRG, the front panel controls can be  
operated.  
INPUT REMOTE and REMOTE  
SYSTEM are enabled when REMOTE  
ENABLE is set to ON.  
CUTO  
Selects CUT OFF setting screen  
Decrease (to min. value)  
Turns the ON-SCREEN  
display on or off. (This  
function is effective only  
in the DRIVE or CUT OFF  
adjustment mode.)  
Trigger system: Controls the function by short-circuiting (short-  
circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)  
VOLUME/  
SELECT (–)  
1
Reverse the setting value  
Selects DRIVE setting screen  
DISP  
DRV  
Switches the input by short-circuiting a specified signal line in  
INPUT A, B, C, or D.  
Notes:  
A/B  
Switches between INPUT A and INPUT B with D-sub pin 2.  
For WHITE BALANCE items, select the CUT OFF or DRIVE  
setting screen, then select the function display for adjustment.  
Press the EXIT (MENU) button to return to the <SET-UP  
MENU> screen.  
(Also, refer to HOW TO USE EXTERNAL CONTROL on page 17.)  
13  
12  
 
HOW TO INITIALIZE THE  
SETTING  
SCREEN DISPLAY AND SELECTIONS IN THE  
<SET-UP MENU> RESET MODE  
BASIC CONNECTION EXAMPLE  
Notes:  
Before connecting your system, make sure that all units are turned off.  
The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected.  
Be sure to refer to the instructions provided with the unit(s) you are connecting.  
Each pair of input (IN) and output (OUT) terminals are bridge-connected.  
If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)  
terminal as this will cause the terminating resistance switch to open (auto terminate function).  
When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components.  
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video  
signal “looping” between the VCRs, and is not a malfunction.)  
Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When both  
VIDEO B terminals are connected (input) at the same time, the Y/C terminal has priority.  
You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and  
the volume level to their factory-set (initial) values.  
<SET-UP MENU> RESET screen  
<SET–UP MENU> RESET  
Are you sure ?  
Yes” then <+>  
1. Press the Power ( ) switch to turn the power  
OFF (activate the standby mode).  
“No”  
then <MENU>  
VIDEO A Connection Example (Select Input A (VIDEO))  
POWER  
VIDEO A  
Video  
Video  
(Video signal cable)  
Video Camera  
(Video signal cable)  
2. While pressing both MENU button and CHROMA/  
PHASE button, press the Power ( ) switch to turn  
Initial settings  
Functions (Items)  
IN  
VIDEO B  
OUT  
Initialization  
(setting)  
Video  
the power ON.  
(Video signal cable)  
IN  
OUT  
Y/C  
APERTURE  
00  
The <SET-UP MENU> RESET screen is displayed.  
ADJ. BAR POSI  
COLOR TEMP  
COLOR SYSTEM  
COMPO. LEVEL  
RUSH DELAY  
LOWER  
6500  
AUTO  
00  
* The screen automatically disappears when no operation  
is performed after about 5 minutes.  
CHROMA MENU  
PHASE  
POWER  
Audio  
Video Monitor  
(Audio signal cable)  
IN  
Note:  
STD  
OUT  
The <SET-UP MENU> RESET screen will not be  
displayed if the MENU or CHROMA/PHASE buttons are  
pressed for a very short time. Keep pressing them until  
the display screen appears.  
PICTURE SUB ADJ.  
AUDIO A  
Audio  
CONTRAST 00  
BRIGHT  
CHROMA  
VCR  
(Audio signal cable)  
00  
00  
00  
00  
00  
OUT  
OUT  
IN  
Video Monitor  
AUDIO B  
Audio  
PHASE  
(Audio signal  
cable)  
IN  
VIDEO B (VIDEO) Connection  
Example (Select Input B (VIDEO))  
H. POSITION  
V. POSITION  
WHITE BALANCE  
3. Setting  
R. CUT OFF 00  
G. CUT OFF 00  
B. CUT OFF 00  
Initialization is required.  
Press the VOLUME/SELECT [+] button.  
* Initialization is completed, and the <SET-UP MENU>  
RESET screen disappears.  
VOLUME/SELECT  
R. DRIVE  
B. DRIVE  
00  
00  
Video  
Video Camera  
CONTROL LOCK OFF  
STATUS DISPLAY ON  
REMOTE SYSTEM MAKE  
(Video signal cable)  
VCR  
Initialization is not required.  
Press the MENU button.  
INPUT REMOTE  
A – D  
MENU  
Video Monitor  
CHROMA  
PHASE  
CONTRAST  
BRIGHT  
00  
00  
00  
00  
Audio  
* Initialization is aborted, and the <SET-UP MENU>  
RESET screen disappears.  
(Audio signal cable)  
Video Monitor  
: Signal Flow  
VCR  
VOLUME  
20  
14  
15  
 
HOW TO USE EXTERNAL  
CONTROL  
BASIC CONNECTION EXAMPLE  
(cont’d)  
VIDEO B (Y/C) Connection Example (Select Input B (Y/C))  
ABOUT EXTERNAL CONTROL  
This monitor is provided with an external control terminal. MAKE (make contact) or TRG. (trigger) system can be selected.  
(MAKE (make contact system): The function is controlled with H and L (short-circuit/open with the 15th pin GND).  
(TRG. (trigger system): The function is controlled by short-circuiting with pulses (for about 1 second) (short-circuit/open with the  
15th pin GND).  
VIDEO A  
* The 14th pin (REMOTE ENABLE) is controlled with MAKE even though TRG. is selected.  
IN  
VIDEO B  
OUT  
Note:  
Video Camera  
When this monitor is externally controlled, the following buttons are disabled.  
MAKE: INPUT-A to D, UNDER SCAN, COLOR OFF, ASPECT on the front panel.  
IN  
OUT  
Y/C  
10  
Y/C (S-video)  
VCR  
9
Connections  
5
4
3
2
1
15  
14  
13  
12  
11  
Connect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the  
3-lines 15-pins D-sub connector. The functions of each terminal are listed below.  
(Y/C (S-video) signal cable)  
IN  
8
7
6
Video Monitor  
Y/C (S-video)  
(Y/C (S-video) signal cable)  
OUT  
The Names and Functions of Terminals  
AUDIO A  
No. Names  
Functions  
Operations (OFF p[ ON)  
*1  
OUT  
OUT  
IN  
Video Monitor  
VCR  
AUDIO B  
1
2
3
4
5
6
7
8
9
TALLY  
Puts on the tally lamp.  
Changes the input to INPUT A  
Changes the input to INPUT B  
Changes the input to INPUT C  
Changes the input to INPUT D  
Put off  
Put on  
Change  
Change  
Change  
Change  
Audio  
Audio  
INPUT A  
INPUT B  
INPUT C  
INPUT D  
not used  
not used  
COLOR OFF  
not used  
Not change  
Not change  
Not change  
Not change  
*2  
*3  
*4  
*5  
*6  
*6  
*8  
*8  
*8  
*8  
(Audio signal cable)  
(Audio signal cable)  
IN  
: Signal Flow  
Changes the picture black-and-white. Not change  
Change  
*6  
10 ASPECT  
11 UNDER SCAN  
12 not used  
Changes the screen ratio to 16:9  
4:3  
16:9  
Makes the screen under-scan  
Over-scan  
Under-scan  
*6  
*6  
*7  
13 not used  
14 REMOTE ENABLE Makes the external control from the  
REMOTE terminal valid or invalid  
Invalid  
Valid  
15 GND  
Used as a ground terminal  
*1 : OFF stands for disconnection, and ON stands for short-circuit.  
*2 : When INPUT REMOTE in the set-up menu is set to A/B, H: INPUT A and L: INPUT B are set.  
*3 : When INPUT REMOTE in the set-up menu is set to A/B, pins not used should not be connected.  
*4 : When INPUT REMOTE in the set-up menu is set to A/B, pins not used should not be connected.  
*5 : When INPUT REMOTE in the set-up menu is set to A/B, pins not used should not be connected.  
*6 : Do not connect.  
*7 : Setting REMOTE ENABLE to ON enables remote control from the REMOTE terminal.  
*8 : INPUT REMOTE setting in the set-up menu (REMOTE SYSTEM shown only when MAKE is selected.)  
For the D-sub pins 2, 3, 4 and 5, 4-pin or 1-pin control can be set with INPUT REMOTE in the set-up menu.  
• 4-pin control: Switches input by short-circuiting a specified signal line in INPUT A to D.  
• 1-pin control: Switches between INPUT-A and INPUT-B only with the 2nd pin of the D-sub connector. In this case, INPUT-C and INPUT-D  
cannot be selected.  
Open (H): INPUT-A  
Short-circuit (L): INPUT-B  
NOTE : When more than two terminals are selected (short-circuited) from INPUT A through INPUT D, signal input is prioritized  
alphabetically (A, B, C, D).  
To control INPUT A through INPUT D, we recommend using the interlock switch, which turns off a switch when another  
switch is turned on.  
17  
16  
 
TROUBLESHOOTING  
Solutions to common problems related to your monitor are described here. If none of the solutions presented here  
solves the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.  
Problems  
Points to be checked  
Is the power plug loosened or disconnected?  
Is the main power turned OFF?  
Measures (Remedy)  
Firmly insert the power plug.  
No power supply.  
Turn the main power ON. (See page 6.)  
Set the connected component correctly.  
No picture with the  
power on.  
Is the video signal output from the connected  
component?  
Is the input signal selected properly?  
Select the required video signal input with the  
Input select button. (See page 9.)  
Is the video cable disconnected?  
Connect the video signal cable firmly.  
(See pages 15 and 16.)  
No sound.  
Is the audio signal output from the connected  
component?  
Set the connected component correctly.  
Is the volume output set to minimum?  
Adjust the speaker volume with the VOLUME/  
SELECT button. (See page 9.)  
Is the audio cable disconnected?  
Connect the audio signal cable firmly.  
(See pags 15 and 16.)  
Shaking picture.  
Is the monitor close to a device generating a  
strong magnetic field?  
Move the device away from the monitor until the  
picture stabilizes.  
No colors, wrong  
color, or dark picture.  
Is the color system selected properly?  
Set COLOR SYSTEM in the <MENU> screen to  
AUTO. (See page 11.)  
Has the picture control setting (CONTRAST,  
BRIGHT, CHROMA or PHASE) been changed?  
Set each picture control to the standard setting.  
(See page 9.)  
Press the COLOR OFF button and BLUE CHECK  
button to adjust. (See page 10.)  
Unnatural, irregularly Is the monitor close to a speaker, magnet or any Move the device away from the monitor and turn  
colored, or distorted  
picture.  
other device generating a strong magnetic field? the monitor’s power off. Wait at least 30 minutes,  
then turn the power on again.  
Dark stripes appear  
at the top and bottom  
of the screen, picture  
vertically squeezed.  
Is the aspect ratio set to 16:9?  
Switch the aspect ratio to 4:3 with the ASPECT  
button on the front panel.  
The overall picture  
size is too small.  
Has the UNDER SCAN button been pressed so  
the UNDER SCAN button lights?  
Press the UNDER SCAN button to turn off the  
button. (See page 4.)  
Function buttons on  
Has control of the buttons been locked? (Has  
Set CONTROL LOCK in the <SET-UP MENU>  
the front panel do not the CONTROL LOCK function been set to ON?) screen to OFF. (See pages 12 and 13.)  
function.  
The INPUT SELECT  
buttons do not  
function.  
Is input selection under external control? (Has  
the REMOTE ENABLE function been set to  
valid?)  
Set REMOTE SYSTEM in the <SET-UP MENU>  
screen to TRG. (See pages 12 and 13.)  
Set REMOTE ENABLE to OFF (invalid).  
(See page 17.)  
The following are not malfunctions:  
When a bright still image (such as a white cloth) is displayed for a long period, it may appear to be colored. This is due to the  
structure of the cathode ray tube and will be deleted when another image is displayed.  
You experience a mild electric shock when you touch the picture tube. This phenomenon is due to a normal buildup of static  
electricity on the CRT and is not harmful.  
The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality  
appears on the screen as well.  
If two or more monitors are operated next to each other, their images may shake or be distorted. This phenomenon is due to  
mutual interference; it is not a malfunction. Move the monitors away from each other until the interference disappears or turn  
the power off on any monitor that is not being used.  
18  
 
TM-H1750CG  
Dimensions  
Unit : inch (mm)  
< Side View >  
< Front View >  
16-1/2 (418.1)  
16-1/8 (407)  
15-5/8 (395)  
1/16  
(1.5)  
12-7/8 (327.5)  
*
UNDER COLOR  
SCAN OFF  
BLUE  
CHECK ASPECT  
POWER  
CHROMA CONTRAST  
VOLUME/SELECT  
MENU  
A
B
C
SLOT  
D
PHASE  
BRIGHT  
INPUT SELECT  
TM-H1750CG  
2-3/4 (68)  
11-3/8 (286)  
11-3/8 (288)  
ø7/8 (20)  
* Asterisks ( ) are used to indicate front panel  
*
dimensions.  
Y/C (Mini DIN 4 pin) terminal  
specification  
2
4
Pin No.  
Signal  
GND (Y)  
GND (C)  
Y
IN  
1
2
3
4
1
2
3
4
Y/C  
OUT  
C
3
1
APPENDIX: CONNECTION EXAMPLES FOR THE  
SDI INPUT CARD  
To use the SWITCHED OUT terminal, the main power must be ON. (Unlike a bridged output, this connector outputs relocked  
digital signals.)  
Signals output from the SWITCHED OUT terminal can be selected with INPUT-C (SDI-1) and INPUT-D (SDI-2) buttons on the  
front panel (or remote control).  
When INPUT-A or INPUT-B is selected, this terminal outputs the signals last selected. In the standby mode, signals from the  
SDI 1 connector are output.  
20  
VP0201  
DP3051  
1-12  
No.51923  
 

Invacare Mobility Aid Tracer 9000 User Manual
JVC CD Player KS FX480R User Manual
JVC Digital Photo Frame HR VP676U User Manual
Keating Of Chicago Fryer 7 05 User Manual
Kenmore Range 3627262 User Manual
Kenwood DVD Player DVF R5060 User Manual
Kicker Speaker KS502 User Manual
KitchenAid Freezer 4KSRF36DT User Manual
Kodak Camcorder Ze2 User Manual
Korg Stereo System AX100G User Manual