JVC Projector Accessories PK CL200U User Manual

®
LAMP REPLACEMENT  
INSTRUCTIONS  
Replacement Lamp Kit  
PK-CL200U  
WARNING:  
This Lamp Kit is for use only with JVC model  
AV-61S902.  
LCT0811-001A  
 
Check the accessories  
Check that nothing is missing. The kit will include:  
• High-Pressure Mercury Lamp  
• Hex Wrench  
• Replacement Instructions  
• Recycling Information Sheet  
• Pre-paid shipping label  
Replacing the Lamp  
1) Turn the television off.  
Press the Power button on the remote control or television’s front panel to  
turn the television off. Wait until the picture has closed and the LED lights  
on the front panel have stopped blinking indicating the lamp cool-down  
cycle is complete.  
Warning: The cool-down cycle cools the lamp from its normal operat-  
ing temperatures. This does not mean the lamp will now be cool  
enough to handle safely. Wait at least one hour before proceeding.  
2) Unplug the television.  
Disconnect the television’s power cord from the AC outlet. Make sure  
the LED lights have stopped blinking before you unplug the televi-  
sion. Never attempt to replace the lamp with the television plugged  
in.  
Continued on the next page  
3
 
3) Remove the left speaker panel.  
The next step is to remove  
the left speaker panel locat-  
ed at the bottom of the front  
of the television cabinet.  
Make sure the television is  
unplugged (see steps 1 and  
2) before removing the  
1. Pull  
2. Lift  
speaker panel.  
To remove the panel - Grab  
Speaker  
the panel from the side near  
Panel  
the top. Gently pull the top  
away from the television.  
When the top part of the  
speaker panel is fully away from the television, lift up. The panel will  
come away from the bottom of the television. Set the panel aside.  
4) Remove the filter cover.  
The lamp is located behind the air fil-  
ter. To access the lamp you will need  
to remove this filter assembly and the  
filter panel covering it. To remove this  
panel you will need a Phillips head  
screwdriver. First loosen the screws  
located at the four corners of the  
Screws  
panel. Once the screws have been  
loosened, slide the cover up until the  
large holes align with the screw  
Filter Cover  
heads. Gently pull the panel away  
from the television and set aside.  
(Please see Appendix A for illustrations for removing the speaker and  
filter covers).  
4
 
5) Removing the filter assembly.  
Next you will need to remove the filter  
assembly. To remove the assembly,  
use a coin to loosen the three large-  
slotted screws fastening the filter  
assembly. When the screws have been  
loosened, slide the filter assembly out  
to remove it.  
Interlock switch  
Coin etc.  
• Do not touch the surface of the filter  
or try to remove it from the filter  
assembly. These actions could  
Filter unit  
Filter  
damage the filter. If the filter is damaged, call a service technician to  
replace the filter.  
WARNING:  
DO NOT attempt to remove the assembly until the lamp has fully  
cooled down. If you feel any heat near the lamp assembly, STOP the  
removal and wait until the lamp has FULLY COOLED.  
NEVER attempt to remove the lamp assembly with the television  
plugged into a wall outlet.  
DO NOT DROP the used lamp. The inside of the lamp is under pres-  
sure. Dropping or other hard shock could cause the lamp to shatter.  
ALWAYS recycle the used lamp. Because the lamp contains a small  
amount of mercury it cannot be thrown out with regular trash. Follow  
the recycling instructions included with the replacement lamp.  
Continued on the next page  
5
 
6) Removing the lamp assembly.  
Using the hex wrench included with the replacement lamp, loosen  
the two hex screws fastening the lamp assembly unit. Remove the  
screws and set aside. When the screws have been removed, remove  
the lamp assembly by grabbing the handle and sliding the assembly  
towards you.  
7) Install the new lamp unit  
Slide the new lamp assembly into the television by holding the han-  
dle attached to the unit. When the new lamp assembly is securely  
installed inside the television,  
Handle  
replace the hex screws using  
the hex wrench. To ensure  
the new lamp assembly sits  
properly inside the television,  
secure the right hex screw  
first, then the left. If the lamp  
assembly does not sit  
Light-source lamp unit  
securely inside the television,  
the television will not turn on.  
Hex wrench  
WARNING!  
Remember, it is very important you DO NOT TOUCH THE GLASS  
SURFACE OF THE NEW LAMP. Please re-read the warnings on  
page 2 regarding the new lamp unit.  
This lamp is only for use with the AV-61S902. It is designed to work  
specifically with the AV-61S902. Using this lamp with a different  
television or other product could cause a malfunction and/or damage to  
the television or the lamp.  
THE USED LAMP MUST BE RECYCLED IN THE US. See the includ-  
ed sheet and page 63 of the AV-61S902’s User’s Guide for detailed  
recycling information for customers in the US.  
The lamp assembly in this product contains mercury. Disposal of the lamp  
assembly may be regulated due to environmental considerations. For  
information on replacement, disposal or recycling procedures, please  
contact JVC Customer Relations at 1-800-252-5722.  
6
 
8) Install the filter unit.  
Position the filter assembly back into its place, being careful not to  
touch the surface of the filter. Position the three screws and tighten  
using an correct-sized coin.  
9) Reinstall the filter cover.  
Place the filter cover over the filter. Insert the four screws and tighten  
them using the screwdriver.  
10) Reinstall the speaker cover.  
Replace the bottom of the speaker cover first. Insert the two pegs  
located at the bottom of the cover into the holes at the bottom lip of  
the television cabinet. When the pegs are in place, gently press the  
top part of the speaker cover against the television to reinstall. Once  
the speaker cover is back in place you may plug the television back  
into the AC power supply and return to normal television viewing.  
If you have read the installation instructions and do not feel comfort-  
able changing the lamp yourself, please call for a service technician.  
Continued on the next page  
7
 
Warning Messages  
If the lamp replacement was successful, the television will operate  
normally. If there was a problem with the installation, one of several  
messages may display on the front panel LED lights.  
Lamp installed on a slant or not fully inside the television.  
If the lamp assembly has been installed into the unit slanted (not flat)  
or is not fully inserted into the lamp housing inside the television,  
when the television is turned on the ON TIMER and POWER light  
will flash. The 10 LEDs will light, then turn off one each five seconds.  
When all LEDs are off, the television still will not display a picture.  
To correct: Reinstall the new lamp assembly. Repeat the lamp instal-  
lation steps, taking care to observe all warnings. Make sure when  
the lamp assembly is reinstalled, it is inserted into the unit so it sits  
FLAT inside the unit.  
• If the ON TIMER light and/or POWER light is flashing you need to  
reset the television. Reset the television by unplugging the power  
cord from the AC outlet and then plugging the cord back into the  
outlet again a little later.  
Filter not properly reinstalled.  
If the filter assembly has not been correctly reinstalled or if the filter  
has been damaged, the television will not turn on. When the Power  
button is pressed the 10 LEDs will turn on, then one will turn off  
every five seconds. When three have turned off the television will  
then enter a cool-down mode and the power will turn off.  
To correct: Check to see that the filter has been installed properly.  
Repeat steps 1 to 5 and 8 to 10. You do not need to remove and  
reinstall the lamp. If the television still does not turn on, the filter may  
have been damaged. Call a service technician for repair.  
If the television does not work properly, or displays a message not  
listed here, call a technician for service.  
8
 
Warranty  
For Canadian model televisions, see the separate sheet for  
Canadian Warranty information.  
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as  
set forth below ONLY TO THE ORIGINAL PURCHASER AT RETAIL to be FREE  
FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original  
retail purchase for the period shown below. (“The Warranty Period”)  
6 Months or  
2000 Hours*  
LABOR 1 YEAR  
PARTS 1 YEAR  
LAMP  
* whichever comes first.  
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES,  
THE DISTRICT OF COLUMBIA AND COMMONWEALTH OF PUERTO RICO.  
WHAT WE WILL DO:  
If this product is found to be defective within the warranty period, JVC will repair or  
replace defective parts at no charge to the original owner.  
Such repair and replacement services shall be rendered during regular business  
hours by JVC authorized service centers. Parts used for  
replacement are warranted only for the remainder of this Warranty Period.  
Televisions with a screen size of 25 inches and larger are covered on  
an in-home basis.  
WHAT YOU MUST DO FOR WARRANTY SERVICE:  
Either contact the selling dealer (retailer) or call 1-800-252-5722 to arrange in-  
home service. In-home service will require clear access to the Television by the  
service technician.  
WHAT IS NOT COVERED:  
This limited warranty provided by JVC does not cover:  
1. Products which have been subject to abuse, accident, alteration, modification,  
tampering, negligence, misuse, faulty installation, lack of reasonable care, or if  
repaired or serviced by anyone other than a service facility authorized by JVC to  
render such service, or if affixed to any attachment not provided with the prod-  
ucts, or if the model or serial number has been altered, tampered with, defaced  
or removed.  
2. Initial installation, installation and removal from "built-in" entertainment centers  
and other mounting systems.  
3. Operational adjustments covered in the Owner’s Manual, normal maintenance,  
including head cleaning.  
9
 
Warranty  
4. Damage that occurs in shipment, due to an act of God, and cosmetic damage.  
5. Signal reception problems and failures due to line power surge.  
6. Products used for commercial purposes (including but not limited to rental).  
*7. Lamp is covered for 6 months or 2000 hours from date of purchase (whichever  
comes first). Labor to replace lamp is not included upon expiration of the lamp  
warranty period.  
8. Accessories.  
9. Batteries (except that Rechargeable Batteries are covered for 90 days from date  
of purchase).  
There are no express warranties except as listed above.  
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED  
WARRANTY OF MERCHANTABILTY, IS LIMITED TO THE DURATION OF THE  
EXPRESS WARRANTY HEREIN.  
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCON-  
VENIENCE, OR ANY OTHER DAMAGES, WHETHER DIRECT, INCIDENTAL OR  
CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES,  
RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR  
ARISING OUT OF ANY BREACH OF THIS WARRANTY, ALL EXPRESS AND  
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY  
AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY  
PERIOD SET FORTH ABOVE.  
Some states do not allow the exclusion of incidental or consequential damages or  
limitations on how long the warranty lasts, so these exclusions or limitations may  
not apply to you. This warranty gives you specific legal rights and you may also  
have other rights which vary state to state.  
JVC COMPANY OF AMERICA  
1700 Valley Road  
DIVISION OF JVC AMERICAS CORP.  
Wayne, New Jersey 07470  
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY. THIS WAR-  
RANTY DOES NOT APPLY. FOR DETAILS OF REFURBISHED PRODUCT WAR-  
RANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY  
INFORMATION PACKAGED WITH EACH REFURBISHED PRODUCT.  
For customer use:  
Enter below the Model No. and Serial No. which is located either on the rear,  
bottom or side of the cabinet. Retain this information for future reference.  
Model No.:  
Serial No.:  
Purchase Date:  
10  
Name Of Dealer:  
 
Authorized Service Centers  
QUALITY  
SERVICE  
HOW TO LOCATE YOUR JVC SERVICE CENTER  
TOLL FREE: 1 (800) 252-5722  
Dear Customer,  
In order to receive the most satisfaction from your purchase, please read  
the instruction booklet before operating the unit. In the event that repairs  
are necessary, please call 1 (800) 252-5722 or visit our website at  
Remember to retain your Bill of Sale for Warranty Service.  
Do not service the television yourself  
Caution  
To prevent electrical shock, do not open the cabinet. There are no user serv-  
iceable parts inside. Please refer to qualified service personnel for repairs.  
Accessories  
To purchase accessories for your JVC product, please call toll free: 1 (800)  
882-2345 or on the web at www.JVC.com  
For service in Canada  
To locate your local JVC service center or dealer in Canada please call:  
In Eastern Canada:  
1 (416) 293-1311  
In Western Canada:  
1 (604) 270-1311  
En Français (Montréal):  
1 (514) 871-1311  
Or visit us on the web at www.JVC.ca  
11  
 
JVC COMPANY OF AMERICA  
Division of JVC Americas Corp.  
1700 Valley Road  
JVC CANADA, INC.  
21 Finchdene Square  
Scarborough, Ontario  
Canada, M1X 1A7  
Wayne, New Jersey, 07470  
 

Infinity Speaker IL100s User Manual
Ingersoll Rand Power Screwdriver 7672 A18 User Manual
Insignia Tablet Accessory NS=CAHCC01 User Manual
John Deere Air Compressor AC1 CG16H User Manual
John Lewis Ventilation Hood JLBIHD908 User Manual
Juniper Networks Network Router M7i User Manual
JVC CRT Television HV 29LPZ A User Manual
JVC Speaker System SP AP300 User Manual
Kawai Electronic Keyboard CA440 User Manual
Kenmore Dishwasher 5871521 User Manual