Knoll Systems Stereo Amplifier GS12 User Manual

GS8 GS12  
GS8 and GS12 Eco-SystemAmplifier specifications:  
Eco-System Power  
Amplifiers  
Inputs:  
Input impedance:  
Outputs:  
Output power:  
Peak output power:  
Ideal impedance:  
8 or 12 gold RCA jacks with adjustable gain  
50k ohms  
5 way gold binding posts  
50 watts RMS per channel (8 ohms)  
100 watts per channel (8 ohms)  
4 – 8 ohms  
Installation Instructions v1.2  
Warning: To be installed and/or used in accordance with  
appropriate electrical codes and regulations.  
Frequency response: 10 Hz – 40 kHz +/- 1dB (1w)  
S/N ratio:  
Over 105 dB A weighted (50 watts)  
Less than 0.1% 20 Hz to 20 kHz  
Less than 0.01% 60 Hz 7 kHz 4:1 (SMPTE)  
17” x 3.5” x 11.5” (432 x 89 x 292 mm)  
Quiet 28 dBA  
THD distortion:  
IMD distortion:  
Dimensions:  
Fan noise:  
Introduction: Thank you for your purchase of a Knoll  
Eco-System multi-channel power amplifier and  
congratulations on your choice. This amplifier is  
specifically designed to save energy when idling, which  
can be most of the time. When compared to similar power  
amplifiers the GS8 and GS12 uses less than 5% of the  
energy required for normal amps to idle.  
Power:  
Standby in Eco-System™ less than 5 watts  
Maximum 750 watts at 117 VAC or 230VAC  
GS8 20 lbs (9 kg); GS12 22 lbs (10 kg)  
Steel chassis, powder coated; glass epoxy  
printed circuit boards  
Weight:  
Construction:  
FEATURES:  
Eco-System™ Circuitry saves energy (and  
money) and increases power.  
12 channels x 50 watts RMS at 8 Ohms (over  
100W peak). GS8 8 channels.  
Individual and automatic channel resetting  
protection for low impedance, overheating,  
overloading, overvoltage and undervoltage.  
Individual gain controls for all channels.  
Electronic Link feature connects stereo inputs  
channel 2 through 6 to channel 1. GS8 connects  
stereo inputs channel 2 through 4 to channel 1.  
Side-mounted thermostatically controlled fan for  
internal cooling.  
Warranty  
Knoll Systems warrants its products sold in the USA and Canada by  
authorized Knoll dealers to be free of defects in materials and  
workmanship. This warranty extends for three full years from the date  
of purchase by the original consumer. Any products returned to Knoll  
Systems and found to be defective by Knoll Systems within the  
warranty period will be repaired or replaced at Knoll Systems option, at  
no charge. Knoll Systems will not be responsible for the actual cost of  
installation or removal of the product, nor for any incidental or  
consequential damages. Some states do not allow the exclusion or  
limitation of incidental or consequential damages, so the above  
limitation may not apply to you. This warranty gives you specific legal  
rights. You may have additional legal rights that vary from state to  
state.  
Two rack spaces (3-1/2”) with optional rack  
mount version.  
145 Tyee Drive Point Roberts, WA 98281  
12140 Horseshoe Way Richmond BC V7A 4V4  
tel (604) 272 4555, fax (604) 272 5595  
Made in Canada GS18 and GS12, 2005, Knoll Systems All Rights Reserved  
 
8. Make sure the speakers in each room are connected in phase  
with the amplifier + going to the speaker +. Out of phase  
speakers give unstable imaging and poor bass response.  
9. Connect the AC power into an outlet than can supply at least  
six amps (750 watts) dedicated to each GS8 or GS12.  
10. After the amp has been turned on adjust the “SENS” pot on  
the rear of the amplifier if necessary. The “SENS” adjustment  
can be adjusted up (clockwise) to make the amp less  
susceptible to be turned on due to nuisance noise and hum. If it  
is adjusted too high, the amp may delay turn on or turn off  
during a quiet music or speech passage.  
Installation  
Installing the amplifier should be relatively easy. With a bit of  
planning, this amplifier will give trouble free service for years.  
1. The most important consideration when installing the  
GS8 and/or GS12 is cooling. This amplifier has a lot of power  
packed into a small chassis size. When installing it in an  
equipment stack, it should be the top component. It needs at  
least 3"-5" of space above the amplifier to allow for adequate  
convection cooling.  
2. When installing the GS8 and/or GS12 in a rack we suggest  
adding a 3-1/2" blank above and below the amplifier. In  
multiple GS8 and GS12 installations, plan for a 3-1/2" blank  
(double) between each amplifier and a 3-1/2" blank on the top  
and bottom. Amplifiers should always be the top components in  
a rack system.  
Caution: Never listen to sound that is distorted. If distorted  
sound is heard, turn the volume down immediately or speaker  
and/or amplifier damage could occur that is not covered by the  
warranty. If this problem persists, contact your dealer.  
User Adjustments and Service: There are no user  
adjustments inside the GS8 or GS12. Your installer may make  
certain gain and sensitivity level adjustments on the rear panel.  
3. The GS8 and GS12 are available as an optional 19" EIA rack  
mount style.  
4. Never operate a GS8 or GS12 on its side, as the cooling  
potential drops significantly when operated on the side.  
5. Connect the GS8 or GS12 RCA inputs to the source  
component outputs with good quality, short as possible RCA  
jack cables. Connect each channel individually.  
6. Connect the GS8 or GS12 speaker outputs to speakers using  
good quality speaker wire. Minimum 16 gauge copper wire is  
recommended with 14 gauge minimum for runs over 30' (10m).  
Fire-rated wire may be required if installing wires inside walls,  
ceilings or floors.  
Caution: The GS8 or GS12 contains no user serviceable parts,  
so do not attempt to open or repair the GS8 or GS12.  
Refer servicing to a qualified technician only or contact the  
factory for information.  
Troubleshooting  
If a problem is encountered with the GS8 or GS12 amplifier, the  
most expedient procedure is to locate the problem and if  
possible repair it before requesting service. Be sure to carefully  
check other system components such as controllers, CD players,  
volume controls, wiring, speakers, etc. that may be at fault.  
Note: Ideally the GS8 and GS12 amplifiers like 6-8 ohm loads.  
Connecting to 4-ohm loads won't hurt the amplifier, but the  
channels connected to 4-ohm loads may occasionally shutdown  
due to overloading. Never connect any GS8 or GS12 amplifier to  
less than 4 ohms.  
Problem  
Power led does  
not light - no sound  
Action  
1. Check that the GS8 or GS12 is plugged  
in.  
2. Test the AC outlet with a lamp.  
3. Check GS8 or GS12 power button is on  
(in).  
7. Individually adjust the channel gains as required. Ideally, all  
gains are fully on (fully clockwise).  
4. Slowly turn down the “SENS”  
adjustment (counterclockwise) on the  
amplifier rear, until the amplifier just  
turns on.  
(continued)  
 
Caution: NEVER connect the GS8 or GS12 to impedances  
less than 4 ohms or amplifier damage not covered by the  
warranty may occur.  
GS12 Rear Panel  
The Link button is normally set to the in position to give  
all six stereo inputs individual sources. When a channel  
Link button is set to the out position, that channel is  
(Left/Right) linked or cascaded to input #1 (without the  
use of Y cords). Any or all combinations of linked inputs 2  
to inputs 6 are possible. When all inputs are linked to  
input one, the input impedance is about 8500 ohms.  
The “SENS” pot controls the level threshold setting of the  
automatic power on and off to all channels. Each channel  
turns on and off individually.  
Power On  
Initially adjust the “SENS” on to about 1/3 level. Turn on a  
source to one or more channels and see if the channel  
turns on (observe the front panel led). With soft music on,  
the channel should sense the music and turn on. If it does  
not turn on, try turning the “SENS” adjustment counter  
clockwise slowly until the channel turns on.  
Note: When linked unused RCA inputs can be used as  
outputs to other amplifiers.  
Power Off  
If the channel does not turn off about 3-30 seconds after  
a source has been muted or shut off, adjust the “SENS”  
slowly clockwise and wait 30 seconds. If it still does not  
turn off, turn it a bit more clockwise and wait another 30  
seconds. Keep doing this until the channel turns off in 3-  
30 seconds.  
Note 1: Ideal speaker impedance is 6-8 ohms.  
 

Jet Tools Saw 708315BTA User Manual
John Lewis Oven JLBIOS662 User Manual
JVC CRT Television GGT0010 001A E User Manual
JVC Security Camera VN V686UAPI User Manual
JVC Stereo System 1209YAMMDWMTS User Manual
K2 Mounts TV Mount K2 A3 S User Manual
Kawai Electronic Keyboard CN31 User Manual
Kenwood Car Video System KDV 7241 User Manual
Kenwood Stereo System HD 7 User Manual
KitchenAid Ventilation Hood LI32NA W10674120B User Manual