Kodak Film Camera C 41RA User Manual

April 2000 J-36  
TECHNICAL DATA / CHEMICALS FOR MINILABS  
Choosing the Right Chemicals for  
Your Minilab  
specifically for minilabs. It provides recommended cycles  
for processing the following films with KODAK  
FLEXICOLOR Chemicals in Processes C-41RA, C-41B,  
and C-41*:  
This publication describes KODAK Chemicals designed  
CHOOSING A FILM PROCESS  
To determine which chemicals to use for your film process,  
locate the process cycle that best matches the sequence of  
processing steps and process times of your minilab.  
The following section describes the three basic process  
cycles for films, and includes a listing of the appropriate  
KODAK FLEXICOLOR Chemicals for each cycle. You can  
use any of these cycles with or without a wash step. If you  
select a washless cycle, carefully follow the  
KODAK ROYAL GOLD Films  
KODAK GOLD Films  
KODAK MAX Films  
KODAK Black & White + 400 Film  
KODAK ADVANTIX 100, 200, and 400 Films  
KODAK ADVANTIX Black & White + 400 Film  
KODAK PROFESSIONAL SUPRA Films  
KODAK PROFESSIONAL PORTRA Films  
recommendations in the footnotes.  
Note: This publication does not discuss KODAK  
FLEXICOLOR SM and EKTACOLOR SM Chemicals,  
which are designed for use only in specific minilabs. For  
detailed information on these chemicals, see KODAK  
Publication No. Z-101, Using KODAK SM Chemicals in SM  
Minilabs.  
It also includes the recommended cycles for processing  
KODAK EKTACOLOR Papers with KODAK  
EKTACOLOR PRIME SP, EKTACOLOR PRIME, and  
EKTACOLOR RA Chemicals for Process RA-4.  
For decades, Kodak has been designing and  
manufacturing films, papers, and chemicals that reduce the  
impact of photoprocessing on the environment. KODAK  
EKTACOLOR PRIME SP Developer Replenisher is a new  
developer for EKTACOLOR Papers that offers even more  
beneficial features. Formulated in a single part, it is  
convenient and easy to use. Intended for minilabs with  
average to high utilization, it will give consistent print  
quality with less effluent discharged and less packaging  
waste than KODAK EKTACOLOR PRIME Developer  
Replenisher. (See CHOOSING A PAPER PROCESS for  
more information on the availability and features of this new  
product.)  
Use the cycles in this publication as guides. You may  
have to modify a cycle slightly to suit the design of your  
processor. The replenishment rates for each cycle are  
intended for a typical mix of Kodak color negative films.  
For more detailed information, see KODAK Publication  
No. Z-100, Using KODAK Chemicals in Minilabs, or Z-131,  
Using KODAK FLEXICOLOR Chemicals.  
Although your choice of chemicals may be limited by  
your minilab’s design and its level of utilization, choosing  
the chemicals recommended in this publication ensures that  
you are using chemicals that provide optimum results with  
the smallest possible environmental impact. We continue to  
develop new products that will further reduce chemical use  
and discharge.  
* Do not process films of older design that require a stabilizing agent for  
image stability in minilab processes using KODAK FLEXICOLOR Final  
Rinse and Replenisher. These films are KODAK VERICOLOR III Film,  
VERICOLOR Slide Film / SO-279/5072, and VERICOLOR Print  
Film 4111. Process these films only in a processor that uses  
FLEXICOLOR Stabilizer III and Replenisher.  
©Eastman Kodak Company, 2000  
 
Starting-Point Replenishment Rates—  
Process C-41B  
Starting-Point Replenishment Rates—  
Process C-41  
Starting-Point  
Replenishment Rate  
Starting-Point  
Replenishment Rate  
Solution  
Solution/Step  
mL/135-24  
Roll  
(mL/m)  
mL/25-Exp  
ADVANTIX Film  
(mL/m)*  
mL/25-Exp  
mL/135-24 Roll  
(mL/m)  
ADVANTIXFilm  
(mL/m)*  
FLEXICOLOR Developer  
Replenisher LORR  
FLEXICOLORDeveloper  
Replenisher LORR  
19 (17)  
5 (4.5)  
35 (32)  
40 (36)  
11.1 (10.2)  
3.4 (3.1)  
24 (22)  
19 (17)  
11.1 (10.2)  
FLEXICOLOR Bleach III  
NR Replenisher  
FLEXICOLOR Bleach III  
NR Replenisher  
5 (4.5)  
3.4 (3.1)  
850 (734)†  
24 (22)  
FLEXICOLOR Fixer and  
Replenisher  
Wash  
1250 (1080)†  
35 (32)  
FLEXICOLOR Fixer and  
Replenisher  
FLEXICOLOR Final Rinse  
and Replenisher  
27 (25)  
Wash  
1250 (1080)†  
850 (734)†  
* These rates are averages based on an estimated film-speed mix in  
25-exposure rolls of KODAK ADVANTIX Films.  
FLEXICOLOR  
Final Rinse and  
Replenisher  
35 (32)‡  
27 (25)‡  
Process C-41  
* These rates are averages based on an estimated film-speed mix in  
25-exposure rolls of KODAK ADVANTIX Films.  
† For a two-stage countercurrent-flow wash. Double this rate for a  
single-stage wash.  
‡ If your minilab uses a final rinse instead of washes, use a  
replenishment rate of 40 mL/135-24 roll (36 mL/m) or  
27 mL/25-exposure roll (25 mL/m) of ADVANTIX Film.  
This process cycle is sometimes used in older minilabs. It most  
commonly includes water washes. To use the washless version  
of this cycle, follow the recommendations in the second  
footnote under the table.  
Process C-41 Cycle  
Monitoring Your Film Process  
Time*  
min:sec  
Temperature  
°C (°F)  
Use KODAK Control Strips, Process C-41, to monitor your  
film process. Follow the procedures described in KODAK  
Publication No. Z-100, Using KODAK Chemicals in  
Minilabs, or Z-131, Using KODAK FLEXICOLOR  
Chemicals.  
Solution/Step  
FLEXICOLOR  
Developer Replenisher  
LORR  
37.8 ± 0.15  
(100.0 ± 0.25)  
3:15  
FLEXICOLOR Bleach  
III NR Replenisher  
38 ± 3  
(100 ± 5)  
4:20 to 6:30  
1:00 to 3:15  
4:20 to 6:30  
2:10 to 3:15  
24 to 41  
(75 to 105)  
Wash†  
FLEXICOLOR Fixer  
and Replenisher‡  
38 ± 3  
(100 ± 5)  
24 to 41  
(75 to 105)  
Wash†  
FLEXICOLOR  
Final Rinse and  
Replenisher  
24 to 41  
(75 to 105)  
1:05  
40 to 68  
(104 to 155)  
Dry  
As needed  
* Immersion time plus crossover time to the next tank. Bleach, fixer, and  
final rinse times are minimums; longer times are acceptable.  
† Use a two-stage countercurrent-flow wash. For a single-stage wash,  
double the replenishment rate.  
If your minilab uses a final rinse step instead of a final wash, eliminate  
both washes. Use three countercurrent-flow final rinse tanks with a  
minimum final rinse time of 2:20 (0:47 in each tank). Use a final rinse  
temperature of 38 ± 3°C (100 ± 5°F) and a replenishment rate of  
40 mL/135-24 roll (36 mL/m).  
‡ Use two countercurrent-flow fixer tanks with equal times in both tanks  
(2:10 to 3:15).  
Choosing the Right Chemicals for Your Minilab J-36  
3
 
Developer Options for Process RA-4 Based on  
Processor Utilization  
CHOOSING A PAPER PROCESS  
KODAK EKTACOLOR PRIME SP Developer Replenisher  
is a new paper developer that is replacing the following  
products:  
4 x 6 - inch  
(102 x 152 cm)  
prints per day:  
500  
750  
1000  
1250  
1875  
2500  
125  
250  
375  
5
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
10  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
SP  
KODAK EKTACOLOR PRIME Developer  
Replenisher  
15  
Tank  
olume  
(Litres)  
20  
25  
30  
KODAK EKTACOLOR PRIME Developer  
Replenisher LORR  
40  
50  
KODAK EKTACOLOR PRIME Developer  
Regenerator  
EKTACOLOR RA Developer Replenisher RT  
EKTACOLOR PRIME SP Developer Replenisher (New)  
Because the new developer will not be available in all  
regions at the same time, this publication includes  
recommendations for EKTACOLOR PRIME SP Developer  
Replenisher and the products it will replace.  
SP  
F002_0994AC  
Most minilabs have been able to use EKTACOLOR  
PRIME Chemicals and realize cost savings and reductions in  
processing-solution waste. EKTACOLOR PRIME SP  
Developer Replenisher offers even greater advantages:  
easier mixing with a single-part concentrate, further  
reductions in replenishment rates and effluents for users of  
EKTACOLOR PRIME Developer Replenisher, and less  
packaging waste. (For information about converting, see  
Converting to KODAK EKTACOLOR PRIME SP Developer  
Replenisher.)  
If your lab operates at low utilization or if your equipment  
has a roller-transport design, KODAK EKTACOLOR RA  
Developer Replenisher RT will continue to provide the best  
process performance.  
Before choosing a Process RA-4 cycle, it is important to  
understand processor utilization and the level of operation of  
your minilab paper processor.  
If EKTACOLOR PRIME SP Developer Replenisher is  
not yet available in your country, use the table and products  
below:  
4 x 6 - inch  
(102 x 152 cm)  
prints per day:  
500  
750  
1000  
1250  
1875  
2500  
125  
250  
375  
5
* * * * * *  
* * * * *  
* * * *  
* * * *  
* * *  
10  
15  
Tank  
Volume  
(Litres)  
20  
25  
30  
* *  
40  
50  
* *  
*
EKTACOLOR RA Developer Replenisher RT  
EKTACOLOR PRIME Developer Replenisher  
EKTACOLOR PRIME Developer Replenisher  
or  
EKTACOLOR PRIME Developer Replenisher LORR  
Processor Utilization  
*
Utilization is a way of expressing how much of your  
processor’s capacity is used. If your processor utilization is  
low, oxidation and evaporation will affect the activity of  
your processing solutions.  
The simplest way to determine your processor utilization  
is to measure “tank turnovers” of your developer tank  
solution. One tank turnover is the point at which the volume  
of replenisher added to the tank equals the volume of the  
processor tank.  
F002_0938AC  
Note: If you use EKTACOLOR PRIME Developer  
Replenisher, use EKTACOLOR PRIME Bleach-Fix  
Replenisher. If your processor operates at low utilization,  
use EKTACOLOR RA Developer Replenisher RT and  
EKTACOLOR RA Bleach-Fix and Replenisher.  
EKTACOLOR PRIME SP Developer Replenisher is  
designed for minilabs that have average to high utilization,  
i.e., a developer tank turnover occurs at least once every four  
weeks. If your paper processor operates at low utilization—  
i.e., it takes longer than four weeks for a developer tank  
turnover to occur—you should use KODAK EKTACOLOR  
RA Developer Replenisher RT and EKTACOLOR RA  
Bleach-Fix and Replenisher. These chemicals contain more  
preservative and are replenished at a higher rate to minimize  
the effects of low utilization.  
To determine the option that is suitable for your minilab,  
use the information in the following charts. To use these  
charts, you need to know the number of prints you process  
each week. Utilization is based on a 10-percent makeover  
rate and a six-day work week.  
4
Choosing the Right Chemicals for Your Minilab J-36  
 
Process RA-4 Cycle—Average Utilization  
This cycle is appropriate for processors with average  
utilization—i.e., a developer tank turnover occurs at least  
once every four weeks.  
Process RA-4 Cycle—High Utilization  
This cycle is appropriate for processors with high  
utilization—i.e., a developer tank turnover occurs at least  
once every two weeks.  
Starting-Point  
Temperature Replenishment  
Starting-Point  
Solution/  
Step  
Time*  
min:sec  
Solution/  
Step  
Time* Temperature  
Replenishment  
Rate  
°C (°F)  
Rate  
mL/m (mL/ft )  
min:sec  
°C (°F)  
2
2
2
2
mL/m (mL/ft )  
EKTACOLOR  
PRIME SP  
Developer  
Replenisher†  
or  
EKTACOLOR  
PRIME SP  
Developer  
Replenisher†  
or  
108 (10)  
37.8 ± 0.3  
(100.0 ± 0.5)  
0:45  
37.0 ± 0.3  
(100.0 ± 0.5)  
0:45  
108 (10)  
EKTACOLOR  
PRIME  
EKTACOLOR  
PRIME  
161 (15)  
Developer  
Replenisher  
Developer  
Replenisher  
LORR  
EKTACOLOR  
PRIME  
Bleach-Fix  
Replenisher  
30 to 36  
(86 to 97)  
EKTACOLOR  
RA 100  
Bleach-Fix  
and  
Replenisher‡  
0:45  
1:30  
108 (10)  
248 (23)  
30 to 36  
(86 to 97)  
0:45  
1:30  
54 (5)  
EKTACOLOR  
PRIME  
Stabilizer and  
Replenisher‡  
30 to 37  
(86 to 99)  
EKTACOLOR  
PRIME  
30 to 37  
(86 to 99)  
248 (23)  
Stabilizer and  
Replenisher§  
As  
needed  
Not over  
96 (205)  
Dry  
As  
needed  
Not over  
96 (205)  
Dry  
* Immersion time plus crossover time to the next tank. For best results,  
use the recommended times with crossover times of 6 seconds or less.  
† This developer may not yet be available in your country. If not, use  
EKTACOLOR PRIME Developer Replenisher in a processor with  
average utilization.  
* Immersion time plus crossover time to the next tank. For best results,  
use the recommended times with crossover times of 6 seconds or less.  
† This developer may not yet be available in your country. If not, use  
EKTACOLOR PRIME Developer Replenisher LORR in a processor  
with high utilization.  
‡ Use four countercurrent-flow stabilizer tanks with equal times in all  
tanks (0:23 in each tank). With three countercurrent-flow tanks, use a  
replenishment rate of 495 mL/m2 (46 mL/ft2); with two  
‡ This product will be renamed KODAK EKTACOLOR PRIME  
Bleach-Fix Replenisher LORR.  
2
2
countercurrent-flow tanks, use 970 mL/m (90 mL/ft ).  
If your minilab uses a countercurrent-flow wash instead of a  
stabilizer, use a wash-water temperature of 30 to 40°C (86 to 104°F).  
For wash times of 1:30 or longer, the wash-flow rate should be  
between 2160 and 10,800 mL/m2 (200 and 1000 mL/ft2). The actual  
rate depends on the number of tanks and the wash time (see KODAK  
Publication No. Z-100, Using KODAK Chemicals in Minilabs, or Z-130,  
Using KODAK EKTACOLOR RA Chemicals).  
§ Use four countercurrent-flow stabilizer tanks with equal times in all  
tanks (0:23 in each tank). With three countercurrent-flow tanks, use a  
replenishment rate of 495 mL/m2 (46 mL/ft2); with two  
countercurrent-flow tanks, use 970 mL/m2 (90 mL/ft2).  
If your minilab uses a countercurrent-flow wash instead of a  
stabilizer, use a wash-water temperature of 30 to 40°C (86 to 104°F).  
For wash times of 1:30 or longer, the wash-flow rate should be between  
2160 and 10,800 mL/m2 (200 and 1000 mL/ft2). The actual rate  
depends on the number of tanks and the wash time (see KODAK  
Publication No. Z-100, Using KODAK Chemicals in Minilabs, or Z-130,  
Using KODAK EKTACOLOR RA Chemicals).  
Choosing the Right Chemicals for Your Minilab J-36  
5
 
Process RA-4 Cycle—Low Utilization  
This cycle is appropriate for processors with low  
utilization—i.e., a developer tank turnover requires longer  
than four weeks.  
Converting to KODAK EKTACOLOR PRIME SP  
Developer Replenisher  
Before converting to EKTACOLOR PRIME SP Developer  
Replenisher, use all of your current stock of EKTACOLOR  
PRIME Developer Replenisher (and EKTACOLOR PRIME  
Developer Regenerator) or EKTACOLOR PRIME  
Developer Replenisher LORR. You do not need to dump  
your current working tank solution.  
Starting-Point  
Solution/  
Step  
Time* Temperature  
Replenishment  
Rate  
min:sec  
°C (°F)  
2
2
mL/m (mL/ft )  
When you begin to use EKTACOLOR PRIME SP  
Developer Replenisher to replenish your existing developer  
tank solution, adjust your replenishment rate to the  
appropriate setting in the following table. If you currently  
use EKTACOLOR PRIME Developer Replenisher LORR,  
you do not need to adjust your replenishment rate.  
EKTACOLOR  
RA Developer  
Replenisher  
RT  
35 ± 0.3  
0:45  
215 (20)  
(95 ± 0.5)  
EKTACOLOR  
RA  
Bleach-Fix  
and  
30 to 36  
(86 to 97)  
0:45  
1:30  
215 (20)  
248 (23)  
Replenishment Rate  
Replenisher  
Current  
Replenishment Rate  
with PRIME SP  
Developer  
Replenisher  
EKTACOLOR  
PRIME  
Stabilizer and  
Replenisher†  
Current  
Developer  
Solution  
30 to 37  
(86 to 99)  
mL/ mL/ mL/ mL/ mL/ mL/ mL/ mL/  
m2 ft2 m* ftm2 ft2 m* ft†  
As  
needed  
Not over  
96 (205)  
Dry  
PRIME  
Developer  
Replenisher  
and  
Developer  
Regenerator  
* Immersion time plus crossover time to the next tank. For best results,  
use the recommended times with crossover times of 6 seconds or less.  
† Use four countercurrent-flow stabilizer tanks with equal times in all  
tanks (0:23 in each tank). With three countercurrent-flow tanks, use a  
161 15 20.5 6.3  
108 10 13.7 4.17  
108 10 13.7 4.17  
2
2
replenishment rate of 495 mL/m (46 mL/ft ); with two  
2
2
countercurrent-flow tanks, use 970 mL/m (90 mL/ft ).  
PRIME  
If your minilab uses a countercurrent-flow wash instead of a  
stabilizer, use a wash-water temperature of 30 to 40°C (86 to 104°F).  
For wash times of 1:30 or longer, the wash-flow rate should be between  
2160 and 10,800 mL/m2 (200 and 1000 mL/ft2). The actual rate  
depends on the number of tanks and the wash time (see KODAK  
Publication No. Z-100, Using KODAK Chemicals in Minilabs, or Z-130,  
Using KODAK EKTACOLOR RA Chemicals).  
Developer  
Replenisher  
LORR  
* Normally, mL per linear metre of paper 127 mm (5 in.) wide.  
† Normally, mL per linear foot of paper 127 mm (5 in.) wide.  
Note: If your process is in control with EKTACOLOR  
PRIME Developer Replenisher, you can also calculate the  
replenishment rate for EKTCOLOR PRIME SP Developer  
Replenisher by multiplying your current rate by 0.67. Then,  
reset the rate (or pump setting) to the new rate. If you need  
help adjusting the replenishment rate, contact your minilab  
manufacturer.  
Monitoring Your Paper Process  
Use KODAK Control Strips, Process RA-4, to monitor your  
paper process. Follow the procedures described in KODAK  
Publication No. Z-100, Using KODAK Chemicals  
in Minilabs, or Z-130, Using KODAK EKTACOLOR RA  
Chemicals.  
6
Choosing the Right Chemicals for Your Minilab J-36  
 
KODAK FLEXICOLOR Final Rinse and Replenisher  
This final rinse is designed with state-of-the-art surfactants  
to reduce deposits and drying marks on processed color  
negative films. It also reduces the potential for biological  
growth in the mixed solution. This means less maintenance  
and less frequent dumping of working tanks. Because the  
new final rinse contains no stabilizing agent, labs will not  
need to provide formaldehyde training or do the associated  
record keeping required by OSHA guidelines. You can use  
the final rinse in minilabs that operate with a wash or a  
washless cycle.  
KODAK CHEMICALS FOR YOUR FILM  
PROCESSOR  
KODAK FLEXICOLOR Chemicals are supplied as  
all-liquid concentrates for easy mixing. They are available in  
sizes that are economical and convenient for minilabs. For  
more information on processing with these chemicals, visit  
KODAK FLEXICOLOR Developer Replenisher LORR  
This developer has low replenishment rates that help reduce  
developer effluent discharge by as much as 50 percent.  
Lower replenishment rates mean less chemical mixing and  
lower cost per roll of film processed. Use only  
FLEXICOLOR Developer Starter LORR to prepare a fresh  
tank solution with FLEXICOLOR Developer Replenisher  
LORR.  
Note: Do not process films of older design that require a  
stabilizing agent for image stability. These films are  
KODAK VERICOLOR III Film, VERICOLOR Slide  
Film / SO-279/5072, and VERICOLOR Print Film 4111.  
Process these films only in a processor that uses  
FLEXICOLOR Stabilizer III and Replenisher. Films of more  
recent design, such as KODAK GOLD, MAX, ROYAL  
GOLD, PROFESSIONAL PORTRA, PROFESSIONAL  
EKTAPRESS, and PROFESSIONAL SUPRA Films require  
no stabilization for image stability. They will have optimum  
image-stability performance when processed with  
Available in sizes to make 5 and 10 litres and 25 U.S. gallons  
(two 12.5-gallon sizes).  
KODAK FLEXICOLOR Developer Starter LORR  
Use this starter to prepare a fresh tank solution from  
FLEXICOLOR Developer Replenisher LORR.  
Available in a size to prepare 8.3 U.S. gallons of developer  
tank solution from developer replenisher.  
FLEXICOLOR Final Rinse and Replenisher.  
Available in sizes to make 5 and 10 litres and 12.5 and  
75 U.S. gallons.  
KODAK FLEXICOLOR Bleach III NR Replenisher  
For use in minilabs using Process C-41B or C-41, this bleach  
offers reduced cost per roll of film and reduced  
replenishment rates and volume of effluent discharged. It  
requires no mixing; it is packaged ready to use. Use  
FLEXICOLOR Bleach Starter to prepare a fresh tank  
solution.  
KODAK CHEMICALS FOR YOUR PAPER  
PROCESSOR  
These chemicals are supplied as all-liquid concentrates for  
easy mixing and handling. They are available in sizes that are  
convenient and economical for minilabs.  
Available in a 5-litre size.  
KODAK EKTACOLOR PRIME SP Developer  
Replenisher  
KODAK FLEXICOLOR RA Bleach Replenisher NR  
This bleach is designed for use in minilabs that use Process  
C-41RA. It requires no mixing; it is packaged ready to use.  
This bleach is also odorless. Use FLEXICOLOR Bleach  
Starter to prepare a fresh tank solution.  
This new developer replenisher is designed for minilabs with  
average to high utilization. Supplied as a single-part  
concentrate, it offers easy and convenient mixing.  
Replenishment rates are significantly lower than those of  
EKTACOLOR PRIME Developer Replenisher.  
Available in sizes to prepare 10 litres and 20 gallons (two  
10-gallon mixes) of replenisher solution.  
Available in a 5-litre size.  
KODAK FLEXICOLOR Bleach Starter  
Use this starter to prepare a bleach tank solution with  
FLEXICOLOR Bleach III NR Replenisher or  
FLEXICOLOR RA Bleach Replenisher NR. This product is  
odorless, non-corrosive, and non-foaming for easy use.  
Available as a 1-gallon concentrate to make 20 U.S. gallons  
of Bleach III NR tank solution or 8.3 U.S. gallons of RA  
Bleach NR tank solution.  
Note: EKTACOLOR PRIME SP Developer Replenisher  
will replace EKTACOLOR PRIME Developer Replenisher,  
EKTACOLOR PRIME Developer Replenisher LORR, and  
EKTACOLOR PRIME Developer Regenerator. The  
discontinuance of these three products will occur at different  
times in different regions.  
KODAK EKTACOLOR PRIME Developer Replenisher  
If new EKTACOLOR PRIME SP Developer Replenisher is  
not yet available in your region, use this developer if your  
minilab processor has a developer tank turnover every  
four weeks (or more frequently).  
KODAK FLEXICOLOR Fixer and Replenisher  
Use this fixer for Process C-41 or C-41B.  
Available in sizes to make 5 litres and 5 and 25 U.S. gallons.  
KODAK FLEXICOLOR RA Fixer and Replenisher  
This fixer is designed for use in minilabs that use Process  
C-41RA.  
Available in sizes to prepare 10 litres and 25 gallons (two  
12.5-gallon mixes) of solution.  
Available in sizes to make 5 and 10 litres.  
Choosing the Right Chemicals for Your Minilab J-36  
7
 
Choosing the Right Chemicals for Your Minilab  
KODAK EKTACOLOR PRIME Developer Replenisher  
LORR  
KODAK EKTACOLOR RA 100 Bleach-Fix and  
Replenisher  
If new EKTACOLOR PRIME SP Developer Replenisher is  
You can use this bleach-fix if your processor has a tank  
turnover at least every four weeks. The replenishment rate is  
75 percent lower than that of EKTACOLOR RA Bleach-Fix.  
This product will be renamed KODAK EKTACOLOR  
PRIME Bleach-Fix Replenisher LORR.  
not yet available in your region, use this developer if your  
minilab consistently operates at high utilization, i.e., a  
developer tank turnover occurs at least once every two  
weeks.  
Available in sizes to prepare 10 litres and 25 gallons (two  
12.5-gallon mixes) of replenisher solution.  
Available in sizes to prepare 5 litres and 5 gallons of solution.  
KODAK EKTACOLOR RA Bleach-Fix and Replenisher  
If it takes more than four weeks to turn over the bleach-fix tank  
solution, use this replenisher. Dilute this concentrate to  
prepare a tank or replenisher solution.  
Available in sizes to prepare 5 and 10 litres and 25 gallons of  
solution.  
KODAK EKTACOLOR PRIME Developer Regenerator  
If new EKTACOLOR PRIME SP Developer Replenisher is  
not yet available in your region, your can use this regenerator  
to regenerate and reuse EKTACOLOR PRIME  
Developer overflow.  
Available in sizes to prepare 10 litres and 25 gallons of  
replenisher solution from developer overflow.  
KODAK EKTACOLOR PRIME Stabilizer and  
Replenisher  
KODAK EKTACOLOR RA Developer Replenisher RT  
If your minilab takes longer than four weeks for a tank  
turnover, use this developer.  
Use this stabilizer in place of a final wash in washless  
minilabs.  
Available in sizes to prepare 5 and 10 litres and  
12.5 gallons of solution.  
Available in sizes to prepare 5 and 10 litres and 25 gallons.  
KODAK EKTACOLOR RA Developer Starter  
To make developer tank solutions, mix this starter with  
KODAK EKTACOLOR PRIME SP Developer Replenisher,  
EKTACOLOR PRIME Developer Replenisher,  
EKTACOLOR PRIME Developer Replenisher LORR, or  
EKTACOLOR RA Developer Replenisher RT according to  
the directions on the starter label.  
MORE INFORMATION  
For the latest version of technical support publications for  
KODAK Products, visit Kodak on-line at:  
The Material Safety Data Sheets for these products are  
available on the Kodak web site:  
KODAK EKTACOLOR PRIME Bleach-Fix Replenisher  
Use this bleach-fix if you use EKTACOLOR PRIME SP or  
PRIME Developer Replenisher. The replenishment rate with  
this bleach-fix is 50 percent lower than the rate for  
EKTACOLOR RA Bleach-Fix and Replenisher.  
Available in sizes to prepare 10 litres and 12.5 gallons of  
solution.  
www.kodak.com/go/MSDS  
Many technical support publications for  
KODAK Products can be sent to your fax machine  
from the Kodak Information Center. Call:  
U.S. 1-800-242-2424, Ext. 33 / Canada 1-800-295-5531  
—Available 24 hours a day, 7 days a week—  
If you have questions about KODAK Products, call Kodak.  
In the U.S.A.:  
1-800-242-2424, Monday–Friday  
9 a.m.–7 p.m. (Eastern time)  
In Canada:  
1-800-465-6325, Monday–Friday  
8 a.m.–5 p.m. (Eastern time)  
Consumer Imaging  
EASTMAN KODAK COMPANY ROCHESTER, NY 14650  
Choosing the Right Chemicals for  
Your Minilab  
Kodak, Advantix, Ektacolor, Ektacolor SM, Flexicolor,  
Flexicolor SM, Gold, Max, Prime, and Royal are trademarks.  
Major Revision 4-00  
Printed in U.S.A.  
KODAK Publication No. J-36  
CAT 849 8800  
 

Indesit Cooktop KD6C35 User Manual
InSinkErator Garbage Disposal 76137 User Manual
Jensen Digital Camera KT7009A User Manual
JVC CRT Television GGT0055 001A H User Manual
JVC Speaker System CA MXKA3 User Manual
Kenmore Microwave Oven 72180012 User Manual
Kensington Marine Lighting 62070 User Manual
KitchenAid Refrigerator 2308307 User Manual
Kodak Scanner 9E8651 User Manual
Kompernass Indoor Fireplace KH 1117 User Manual