™
®
iRobot Verro
quick start guide
An easy step-by-step guide to using the
iRobot Verro Pool Cleaning robot
™
irobot® Verro quick start guide
How Verro Works
Place Verro in the water and rock it
Position the handle diagonally across
Verro. Press button on the handle lock
mechanism to move handle.
1
3
from side to side to allow air to escape.
Let Verro settle to the bottom of the pool.
Ensure that it is right side up and level.
Verro has a powerful motor that pumps
80 gallons of water per minute through
the robot, generating suction at two
vacuum intakes under the robot. The
water passes through a filter bag that
traps dirt and debris down to two microns
in size. (For comparison, the period at the
end of this sentence is more than 500
microns in size.)
The force of the water being pumped up
through the bottom of the robot and out
through the top helps Verro maintain
traction on the pool bottom and walls.
Brushes at the front and back of the
robot loosen particles attached to the
walls and bottom of your pool so that they
can be vacuumed up, along with all of the
other loose dirt and debris.
Place the Power Supply at least 12 feet
from pool.
Uncoil the floating power cord and spread it
over the surface of the water.
4
2
5
Plug the floating power cord into the Power Supply. Be sure not to force the plug as it will only go in one
way. Once the plug is fully seated, turn the locking collar clockwise to lock it.
Verro’s coverage algorithm allows Verro
to brush and clean your pool all the way
from the bottom to the waterline in only
60 – 90 minutes.
tip
clean the filter bag regularly. Verro
uses the force of the water pumped
through its filter bag to maintain
traction, particularly on the walls
of the pool. if the filter bag is not
kept clean, Verro will not clean
properly and will not be able to
climb the walls of the pool.
Push and rotate clockwise
6
Ensure the Power Supply is at least 12 feet from the pool and plug it into a GFCI outlet. Ensure the
electric outlet has been properly grounded. Never leave the Power Supply plugged in when Verro is not
in use.
Warning: to prevent risk of electrical shock, Verro must be used only with a
properly installed and functioning ground Fault current interrupter outlet.
tip
change the direction of the handle
before each cleaning run to prevent
the floating power cord from
becoming twisted and to improve
coverage of the entire pool.
t
f
3.5m/12
tip
store Verro in a dry place out of
direct sunlight at a temperature
between 50 and 104 degrees
Fahrenheit. the Power supply is
water resistant, but not waterproof
and may be damaged by rain.
Failure to properly store Verro will
result in loss of warranty.
Press the green Power button to start Verro; the light on the Power Supply will illuminate and Verro will
start. The length of the cleaning cycle will vary based on pool size. To stop Verro before the end of the
cleaning cycle, press the red Power button on the Power Suppy.
7
tip
irobot recommends using
the mesh filter bag (available
when the pool contains a
significant quantity of large debris
(leaves, etc.), such as when the
pool is opened for the season.
the fine filter bag is ideal for
filtering small debris (algae, sand,
etc.) and for regular maintenance.
Light
LigHt: Light indicates that the
On
Off
robot is ON
ON: Green button turns the
robot ON
OFF: Red button turns the
robot OFF.
tip
Periodically straighten the floating
power cord with the detangler.
™
irobot® Verro quick start guide
Quick Start
(cont...)
When Verro has finished cleaning the pool, it will stop automatically and the light
on the Power Supply will go OFF.
Use the floating power cord to pull Verro to the edge of the pool, and then use the
handle to lift Verro out of the water. Water will drain from Verro as it is lifted.
8
12
Wait 20 minutes before removing Verro from the pool to allow the motors to cool.
Shut off and unplug the Power Supply every time you remove the cleaner from
the water. Always remember to turn the Power Supply OFF and unplug it from
the power outlet before removing the cleaner from the pool.
9
Unplug the Power Supply from the GFCI outlet.
Never leave the Power Supply plugged in when Verro is not in use.
10
11
Unplug the floating power cord from the Power Supply.
see Owner’s Manual
for detailed product
instructions.
Rotate counter-clockwise
and pull to unlock
Visit
www.irobot.com/usetips
for instructional photos
© 2007 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. All rights reserved. iRobot is a registered trademark and Verro is a trademark
of iRobot Corporation. Cover photo © Veer incorporated 2002 - 2005. All rights reserved.
|